Johnson Controls IQLOCKDOWN, Руководство по установке, Страница: 3 / 18

INSTALLATION MANUAL 2
REGULATORY INFORMATION: UL 60950-1, UL 294, UL-10C, CAN/ULC S104
Use caution when installing IQ Lockdown on a doorway during installation and use.
Owner is responsible for reading and following the operating and safety instructions as well as proper use of the lock. Wear
appropriate protective items during installation to avoid injury.
Do not install near live electrical cords. Ensure installation area is free of wires, cables, pipes, and other objects that may cause
hazards.
Use only the tools referenced in the installation guide. Use of other tools or not following installation instructions may result in
improper installation and decreased functionality.
Owner is responsible for proper use and avoidance of IQ Lockdown as a bump hazard.
Install IQ Lockdown on solid core, commercial doors only. Installation on hollow core doors will severely degrade the lock’s
capabilities and is not recommended.
Owner is responsible for ensuring the unit is clean for full functionality and capabilities.
Owner is responsible for providing access to the building or commercial facility. Owner is responsible for ensuring alternate access
into the building when needed.
Owner is responsible for maintaining control of permissions, access control, and accountability of any key fob or credentialed device
that has been shared with the lock.
The unit is designed to act as a deterrent, but should still be used in conjunction with other safety measures. The unit is intended as
supplementary security for use in conjunction with current lock hardware.
Johnson Controls is not liable for any personal injuries, property damage, economic loss or any consequential damages sustained as
a result of any individual that comes into contact with the lock or attempts to breach it.
Do not consume any area of the unit.
Do not put the unit near sensitive bodily areas.
Do not place fingers near the center locking gate or bracketing hardware while the lock is being used. Severe injury to fingers could
result from getting caught between the locking gate and bracket.
To avoid damage to the unit, do not use on wet surfaces or damp locations. The product is designed for indoor use only. Do not
expose to weather elements as this may affect functionality.
To avoid potential damage to your unit, do not simulate a breach. Damage to the unit may affect later functionality.
Owner is responsible for ensuring unit is operating properly. Johnson Controls expressly disclaims all guarantees, whether implied or
expressed, to include but not limited to fitness or merchantability for a particular purpose.
!
CAUTION
CAUTION
NOTICE
WARNING: Changes or modifications which are not expressly approved by Johnson Controls could void the user’s authority to operate the equipment.
AVERTISSEMENT: Les changements ou modifications qui ne sont pas approuvés par HavenLock Inc. and Johnson Controls pourrait annuler l'autorité de l'utilisateur de faire
fonctionner l'équipement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is
subject to the following two conditions:
1) This device may not cause interference.
2) This device must accept any interference, including interference that may cause undesired operation of the device.
Cet appareil contient des émetteurs / récepteurs exemptés de licence conformes aux RSS (RSS) d'Innovation, Sciences et Développement économique Canada. Le
fonctionnement est soumis aux deux conditions suivantes:
1) Cet appareil ne doit pas causer d'interférences.
2) Cet appareil doit accepter toutes les interférences, y compris celles susceptibles de provoquer un fonctionnement indésirable de l'appareil.
This system has been evaluated for RF Exposure per RSS-102 and is in compliance with the limits specified by Health Canada Safety Code 6. The system must be installed at a
minimum separation distance from the antenna to a general bystander of 20cm to maintain compliance with the General Population limits.
L’exposition aux radiofréquences de ce système a été évaluée selon la norme RSS-102 et est jugée conforme aux limites établies par le Code de sécurité 6 de Santé Canada.
Le système doit être installé à une distance minimale 20 cm séparant l’antenne d’une personne présente en conformité avec les limites permises d’exposition du grand public
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
20 Minute - 45 Minute Rating
Test Standard: UL 10C, NFPA 252, CAN/ULC S104
Guardian Fire Testing Laboratories Inc.
ISO 17020, 17025, 17065
Firetesting.com
It is recommended that the product shall be installed in accordance with the
applicable requirements in NFPA 101 (chapters 14, 15), NFPA 80, IBC/IFC, NFPA
72 and the Authority Having Jurisdiction (AHJ).
Regulatory Note:
SGS has evaluated and certified this product for safety under UL 294, 7th Ed. Jan. 31, 2018, UL 60950-1, 2nd Ed., Rev. May 9, 2019, CAN/CSA C22.2 No. 60950-1-07, as a commercial
locking device. Utilize SGS reference number 800596 and SGSNA/20/SUW/00006 for additional information related to this standard.
RF Exposure:
This device is currently SAR exempt.
RF Communication:
The installer shall performan an RF communication verification before finalizing the location of the lock to ensure proper signal strength is received from the compatible control
panel using Z-Wave communication.
Safety Notes:
Ensure that the provided wall charger adapter and wire accessory cable are used to charge the device as necessary. Utilizing anything other than provided could cause a shock or hazard
rendering the device inoperable as well as potential injury.