Johnson Controls Intelligent Fire Integrator NION-16C48M Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 40

background image

NION Hardware Connections

Description and Installation

15

NION-16C48M Installation & Operation Manual - P/N: 53347:Rev: A1 5/5/09

FTXC Network Transceivers

The FTXC transceiver allows up to 8,000 feet (2438.4 m) per segment in a point-to-point
configuration, up to 6,000 feet (1828.8 m) per segment in a dedicated bus configuration, or up to
1,500 feet (457.2 m) per segment in a star configuration. Each segment can support 64 FTXCs, and
with routers, the system can be expanded up to 200 nodes. A maximum load of 30 ohms on each
leg of the Echelon wire network is permitted.

Figure 2.5 FTXC Network Transceiver Board Layout

Header Connection

Bus Termination

Electrical Termination Jumper

Data B

Data A

Free Termination

«
...
13
14
15
16
17
...
»

Содержание Intelligent Fire Integrator NION-16C48M









































Отзывы:

Нет отзывов

Похожие инструкции для Intelligent Fire Integrator NION-16C48M

Бренд: Panasonic Страницы: 44

Бренд: Panasonic Страницы: 32

HomeHawk KX-HNC800

Бренд: Panasonic Страницы: 2

BL-C10A - Network Camera - Pan

Бренд: Panasonic Страницы: 4

Бренд: Messoa Страницы: 32

Бренд: Abus Страницы: 353

WIRELESS ALARM SYSTEM

Бренд: Abus Страницы: 14

Бренд: Abus Страницы: 11

Бренд: Abus Страницы: 110

Бренд: Abus Страницы: 82

Бренд: Abus Страницы: 18

Бренд: Abus Страницы: 18

Бренд: Abus Страницы: 16

WIRELESS ALARM SYSTEM

Бренд: Abus Страницы: 101

Бренд: Abus Страницы: 33

Бренд: Abus Страницы: 99

Бренд: EasyPro Страницы: 8

Бренд: Cambridge SoundWorks Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды