Johnson Controls G670 Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 24

background image

Installation Sheets Manual 121

Gas Combustion Combination Controls and Systems Section

G

Technical Bulletin G670

Issue Date 0300

© 2000 Johnson Controls, Inc.

1

Part No. 24-8143-162, Rev. B

www.johnsoncontrols.com

Code No. LIT-121240

Figure 1: G670 Intermittent Pilot Ignition Control

The G670 is a Non-100% Lockout Intermittent Pilot Ignition (IPI) control
that replaces the G67AG and G67BG ignition controls. The G670 is used to
automatically light a pilot burner and energize the main burner gas valve in
response to a call for heat from the system thermostat. When the call for heat
is satisfied, the thermostat opens and the G670 de-energizes the pilot and
main burner gas valves.

Following are the application requirements of the G670 control.

•

The G670 can be used with equipment with a maximum firing rate of
117 kW (400,000 Btu/hr). Any application greater than 117 kW
(400,000 Btu/hr) must have written approval in advance from the
Heating Products Engineering Department.

•

All G670 applications must use a redundant gas valve system with the
main valve seats in series.

G670 Intermittent Pilot Ignition Controls

Description

Application
Requirements

1
2
3
...
»

Содержание G670

























Отзывы:

Нет отзывов

Похожие инструкции для G670

Бренд: Rayrun Страницы: 2

Бренд: IDenticard Страницы: 2

Бренд: 3Ware Страницы: 2

Бренд: UniKey Страницы: 20

Бренд: Mamas & Papas Страницы: 16

Бренд: Samsung Страницы: 27

Бренд: Acclaim Lighting Страницы: 32

Бренд: Jeep Страницы: 19

Бренд: Veer Страницы: 2

Бренд: Jabra Страницы: 18

Бренд: Mackie Страницы: 16

Бренд: TANDBERG Страницы: 47

Бренд: Vanderbilt Страницы: 2

FT-2000 - MENU MODE LIST

Бренд: Yaesu Страницы: 56

Бренд: CAME Страницы: 2

Бренд: Vag Страницы: 15

Бренд: Technische Alternative Страницы: 68

Бренд: TechGrow Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды