manualshive.com logo in svg

Johnson Controls FX80, Руководство по установке, Страница: 10 / 12

Поделиться
Скачать
Johnson Controls FX80 Скачать руководство пользователя страница 10

Table 3: LEDs and descriptions

Callout

Description

1

Wi-Fi (Green) 

- Lit when Wi-Fi configuration switch is not off

2

RS-485 A (COM1)

 - Transmit (TX) and Receive (RX)

3

RS-485 B (COM2)

 - Transmit (TX) and Receive (RX)

4

STAT (Green)

 - Remains lit when controller is powered

5

BEAT (Yellow)

 - Heartbeat, normally 1 Hz 50% duty cycle

6

Secondary Ethernet 

- SEC (LAN2) Link and Activity

7

Primary Ethernet 

- SEC (LAN1) Link and Activity

8

(Behind door) BACKUP (Green)

 - Typically off

If the 

BEAT

 LED stays on constantly, does not light, or blinks very fast, have your ABCS Distributor

contact the FSC or your appropriate technical support group.

Important: 

 The 1 Hz, 90/10 percent on/off 

BEAT

 flash at startup also occurs during other

critical operations, such as a firmware upgrade to the controller or any attached modules.

To be safe, do not remove power from the controller while its 

BEAT

 LED flashes with a 90/10

percent on/off duty cycle. Wait for the normal (50/50 percent) flash to return before removing

power.

Remove or replace the microSD flash memory card

If necessary, you may need to remove or replace microSD flash memory card.

Figure  9: MicroSD card location in Controller

Table 4: MicroSD card location in Controller

Callout Description
1

Access shutter for the microSD card (slide to open or close)

2

Card carrier inside the controller

3

MicroSD card to insert or remove from the card carrier

Important: Disconnect all power

 to the controller 

before removing or inserting

 the

microSD card. Otherwise, equipment damage is likely to occur.

FX80 Supervisory Controller Installation Instructions

10

Содержание FX80













Отзывы:

Нет отзывов