manualshive.com logo in svg

Johnson Controls FMS-2000C, Руководство пользователя, Страница: 2 / 62

Поделиться
Скачать
Johnson Controls FMS-2000C Скачать руководство пользователя страница 2

FMS-2000C

LIT-12013504

2

Risk of Personal Injury or Property Damage.

For use in a controlled environment only. Refer to installation instructions for environmental conditions.

Risk of Electric Shock.

Disconnect the power supply before making electrical connections. Contact with components carrying hazardous voltage can cause 

electric shock and may result in severe personal injury or death.

Risk of Electric Shock.

Disconnect all electric power sources from the FMS-2000C Critical Environment Controller before removing the FMS-2000C controller 

cover. Contact with internal components carrying hazardous voltage can cause electric shock and may result in severe personal injury 

or death.

Risk of Property Damage.

Do not apply power to the system before checking all wiring connections. Short circuited or improperly connected wires may result in 

permanent damage to the equipment.

Risk of Property Damage.

Do not run low-voltage cable in the same conduit or wiring troughs with high-voltage wires. Running low- and high-voltage wires in the 

same conduit or wiring troughs may damage the equipment or cause system malfunction.

Risk of Property Damage.

Ensure that the power source conforms to the requirements of the equipment. Failure to use a correct power source may result in 

permanent damage to the equipment.

Risk of Property Damage.

Do not run network communication cables in the same conduit, raceway, or panel with any high-voltage (greater than 30 VAC) wiring. 

Isolate all network wiring and all network devices from high-voltage wiring and equipment. Failure to isolate network wiring and 

network devices from high-voltage wiring and equipment can result in damage to network devices or poor network performance.

Risk of Property Damage.

Label all wires prior to disconnecting the equipment. Failure to label the wires may cause improper equipment operation after 

reconnecting the equipment.

Risk of Property Damage

Do not use a single transformer to power both the actuator and the controller. Use a 24 VAC 30 VA Class 2, Limited Energy, or LPS for 

the controller, and a separate 24 VAC 20 VA Class 2, Limited Energy, or LPS for the actuator. Failure to follow the wiring diagrams may 

result in damage to the actuator, the transformer, the controller, or all devices and could void your warranty.

 IMPORTANT:

 Do not install or use this FMS-2000C Critical Environment Controller in or near environments where corrosive substances

 or vapors could be present. Exposure of the FMS-2000C Critical Environment Controller to corrosive environments may damage the

 device’s internal components and will void the warranty.

 IMPORTANT:

 Do not install this FMS-2000C Critical Environment Controller in condensing, wet, or damp environments. Moisture may

 cause damage to the FMS-2000C controller.

 IMPORTANT:

 Only qualified personnel should install or service Johnson Controls products. These instructions are a guide for such

 personnel. Carefully follow all instructions in this document and all instructions for the FMS-2000C Critical Environment Controller.

Note: 

The actuator is sold separately.

Содержание FMS-2000C































































Отзывы:

Нет отзывов