Johnson Controls FAC3611 Скачать руководство пользователя страница 17

Страница: 17 / 22

Figure 11: End-of-Line switch positions

To set the EOL switch on a field controller, complete the

following steps:

Determine the physical location of the controller on

the FC bus.

Determine if the controller must be set as a

terminating device on the bus.

Note:

For detailed information regarding EOL

termination rules and EOL switch settings on FC

buses, refer to the

MS/TP Communications Bus

Technical Bulletin (LIT-12011034)

If the controller is a terminating device on the FC

bus, set the EOL switch to ON. If the controller is not

a terminating device on the bus, set the EOL switch

to Off.

When a controller is connected to power with its EOL

switch set to ON, the amber EOL LED on the controller

cover is lit.

Setting the Input Jumpers

CAUTION

Risk of Electric Shock:

Disconnect supply power to the controller before at-

tempting to adjust the Binary Output Source Power

Selection Jumpers. Failure to disconnect the supply

power may result in electric shock.

ATTENTION

Risque de décharge électrique

Débrancher l'alimentation de l'controller avant tout

réglage du Binary Output Source Power Selection

Jumpers. Le non-respect de cette précaution risque

de provoquer une décharge électrique.

UI current loop jumpers

The UI current loop fail-safe jumper pins are located on

the circuit board under the controller cover near the UI

terminals.

Note:

Current Loop Jumpers

are not included

with

the MS-FAC3611-0A. (Asia only model.)

Figure 12: Current loop jumper positions

Set the current loop jumper to the Enabled position

(Figure 12) to connect an internal 100 ohms resistor

across the UI terminals, which maintains the 4–20 mA

current loop circuit even when power to the controller is

interrupted or off.

Important:

Current loop jumpers must be in the

Disabled (default) position for all UIs that are not set

up to operate as 4–20 mA analog inputs.

The following table identifies the current loop switches

associated with each UI on the controller.

Table 7: FAC3611 UI Inputs and jumper labels

Universal Input label

Jumper label on circuit board

IN1

IN2

IN3

IN4

IN5

IN6

J10

IN7

J11

IN8

J12

Commissioning Field Controllers

You commission BACnet MS/TP field controllers with

the (Controller Configuration Tool ) CCT software.

The controller can be connected using NxE Passthru,

Bluetooth (using BTCVT), or through MAP 4.2+/BACnet

Router (Mobile Access Portal (MAP) Gateway at version 4.2

or above). Refer to

Controller Tool Help (LIT-12011147)

for

detailed information on commissioning field controllers. .

Note:

The MAP Gateway serves as a replacement for

the BTCVT, which is no longer available for purchase,

but continues to be supported.

FAC3611 Advanced Application Controller Installation Guide

Содержание FAC3611























Результаты поиска

Содержание FAC3611

Отзывы:

Похожие инструкции для FAC3611

Бренды по названию

Популярные бренды

Johnson Controls FAC3611, Руководство по установке

Результаты поиска

Содержание FAC3611

Отзывы:

Похожие инструкции для FAC3611

Бренды по названию

Популярные бренды