Johnson Controls FAC2611 Скачать руководство пользователя страница 18

Страница: 18 / 24

Removing the Controller cover

Important:

Electrostatic discharge can damage

controller components. Use proper electrostatic

discharge precautions during installation, setup, and

servicing to avoid damaging the controller.

Important:

Disconnect all power sources to the

controller before removing cover and changing

the position of any jumper or the EOL switch on

the controller. Failure to disconnect power before

changing a jumper or EOL switch position can result

in damage to the controller and void any warranties.
The controller cover is held in place by four plastic

latches that extend from the base and snap into

slots on the inside of the housing cover.
To remove the controller cover:

Place your fingertips under the two cover lift tabs on

the sides of the housing cover and gently pry the top

of the cover away from the base to release the cover

from the two upper latches.

Pivot the top of the cover further to release it from

the lower two latches.

Replace the cover by placing it squarely over the

base, and then gently and evenly push the cover

on to the latches until they snap into the latched

position.

Figure 10: FAC26 with cover removed showing EOL

switch and jumper positions

Setting the End-of-Line (EOL) switch

Each field controller has an EOL switch, which, when set

to ON, sets the controller as a terminating device on the

bus. See

Removing the Controller cover

for the EOL switch

location. The default EOL switch position is Off.

Figure 11: End-of-Line switch positions

To set the EOL switch on a field controller:

Determine the physical location of the field controller

on the FC bus.

Determine if the controller must be set as a

terminating device on the bus.

Note:

Refer to the

MS/TP Communications Bus

Technical Bulletin (LIT-12011034)

for detailed

information regarding EOL termination rules and

EOL switch settings on FC buses.

If the controller is a terminating device on the FC

bus, set the EOL switch to ON. If the controller is not

a terminating device on the bus, set the EOL switch

to Off.

When a controller is connected to power with its EOL

switch set to ON, the amber EOL LED on the controller

cover is lit.

Setting the Input Jumpers

CAUTION

Risk of Electric Shock:

Disconnect supply power to the field controller before

attempting to adjust the Binary Output Source Power

Selection Jumpers. Failure to disconnect the supply

power may result in electric shock.

ATTENTION

Risque de décharge électrique

Débrancher l'alimentation de l'controller avant tout

réglage du Binary Output Source Power Selection

Jumpers. Le non-respect de cette précaution risque

de provoquer une décharge électrique.

FAC2611 Advanced Application Field Equipment Controller Installation Guide

Содержание FAC2611

























Результаты поиска

Содержание FAC2611

Отзывы:

Похожие инструкции для FAC2611

Бренды по названию

Популярные бренды

Johnson Controls FAC2611, Руководство по установке

Результаты поиска

Содержание FAC2611

Отзывы:

Похожие инструкции для FAC2611

Бренды по названию

Популярные бренды