Johnson Controls FAC2611-0U Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 25

Johnson Controls FAC2611-0U Скачать руководство пользователя страница 23

Troubleshooting Field Controllers

Observe the Status LEDs on the front of the field controller and see table below to troubleshoot the controller.

Table 8: Status LEDs and Descriptions of LED States

Description of LED States

Normal LED
State

LED Color

LED Label

Off Steady = No Supply Power or the controller’s polyswitch/resettable fuse
is open. Check Output wiring for short circuits and cycle power to controller.

On Steady = Power Connected

On Steady

Green

POWER

Off Steady = No Faults

On Steady = Device Fault; no application loaded; Main Code download
required, if controller is in Boot mode.

Blink - 2 Hz = Download or Startup in progress, not ready for normal operation

Rapid blink = SA Bus communications issue

Off Steady

Red

FAULT

Blink - 2 Hz = Data Transmission (normal communication)

Off Steady = No Data Transmission (N/A - auto baud not supported)

On Steady = Communication lost, waiting to join communication ring

Blink - 2 Hz

Green

SA BUS

Blink - 2 Hz = Data Transmission (normal communication)

Off Steady = No Data Transmission (auto baud in progress)

On Steady = Communication lost, waiting to join communication ring

Blink - 2 Hz

Green

FC BUS

On Steady = EOL switch in ON position

Off Steady = EOL switch in Off position

Off (Except on
terminating
devices)

Amber

EOL

Repair Information

The MS-FAC2611-0U model is UL 864 10th Edition
UUKL/ORD-C100-13 UUKLC listed for smoke control. If
a field controller fails to operate within its specifications,
contact the Johnson Controls Repair Center in Louisville,
Kentucky, at 1-502-671-7312.

Accessories

See

for field controller accessories ordering information.

Table 9: Accessories Ordering Information

Description

Product Code Number

Transformer, 120/24 VAC, 96 VA, with circuit breaker and 120 VAC outlet, approved for Smoke
Control

PAN-PWRSP-U

Technical Specifications

Table 10: FAC2611-0U Field Application Controller

MS-FAC2611-0U Field Application Controller, UL/cUL 864 Listed for Smoke Control

Product Code Numbers

24 VAC (nominal, 20 VAC minimum/30 VAC maximum), 50/60 Hz, power supply
Class 2 (North America)

Supply Voltage

23

FAC2611-0U Advanced Application Field Equipment Controller Installation Instructions

«
...
21
22
23
24
25
»

Содержание FAC2611-0U


























Отзывы:

Нет отзывов