Johnson Controls DIS1710 Скачать руководство пользователя страница 6

Technical specifications

Table 2: DIS1710 Local Controller display

Product Code Number

MS-DIS1710-0 Local Controller Display for Field Equipment Controllers

Power Requirement

Nominal 15 volts provided by controller over SA Bus.

Power Consumption

2 VA maximum

Ambient Operating

Temperature

0°C–50°C (32°F–122°F)

Ambient Operating

Conditions

10%–90% RH, 30°C (86°F) maximum dew point

Ambient Storage

Temperature

-40°C–70°C (-40°F–158°F)

Ambient Storage

Conditions

5%–95% RH, 30°C (86°F) maximum dew point

Terminations

RJ-12 6-pin jack at Service Port (covered by removable cap-plug) SA Bus connection on back of unit

Processor

Renesas

®

 H8S-2398 16-bit microprocessor

Memory

256 KB Flash Memory 8 KB Random Access Memory (RAM)

Operating System

RTOS-H8S

Network and Serial

Interfaces

Communication to controller over SA Bus

Graphic Display

Resolution

240 x 64 pixels with white LED backlighting (adjustable)

Dimensions (Height x

Width x Depth)

85.9 mm x 238 mm x 25.8 mm (3.4 in. x 9.37 in. x 1.0 in.)

Housing

Plastic housing material: ABS + polycarbonate
Protection: IP20 (IEC60529)

Mounting (Height x

Width)

Mount to the outside of the enclosure 70.5 mm x 216.5 mm (2.78 in. x 8.525 in.)

Shipping Weight

0.14 kg (0.3 lb)

United States:

 UL Listed, File E107041, CCN PAZX, UL 916, Energy Management Equipment; FCC Compliant

to CFR47, Part 15, Subpart B, Class A

Canada:

 UL Listed, File E107041, CCN PAZX7, CAN/CSA C22.2 No. 205, Signal Equipment; Industry Canada

Compliant, ICES-003

Europe:

 CE Mark – Johnson Controls, Inc. declares that this product is in compliance with the essential

requirements and other relevant provisions of the EMC Directive.

Compliance

Australia and New Zealand:

 RCM Mark, Australia/NZ Emissions Compliant

The performance specifications are nominal and conform to acceptable industry standards. For application at

conditions beyond these specifications, consult the local Johnson Controls office. Johnson Controls, Inc. shall not be

liable for damages resulting from misapplication or misuse of its products.

Product warranty

This product is covered by a limited

warranty, details of which can be found at

www.johnsoncontrols.com/buildingswarranty.

Single point of contact

APAC

Europe

NA/SA

JOHNSON CONTROLS
C/O CONTROLS PRODUCT
MANAGEMENT
NO. 32 CHANGJIJANG RD NEW
DISTRICT
WUXI JIANGSU PROVINCE 214028
CHINA

JOHNSON CONTROLS
WESTENDHOF 3
45143 ESSEN
GERMANY

JOHNSON CONTROLS
507 E MICHIGAN ST
MILWAUKEE WI 53202
USA

For more contact information, refer to

www.johnsoncontrols.com/locations.

© 2019 Johnson Controls. All rights reserved. All specifications and other information shown were current as of document revision and

are subject to change without notice.

www.johnsoncontrols.com

Содержание DIS1710







Отзывы: