Ø
n.176 (Sub Menu 1/5): Press five for standard audio
verification sensitivity.
Ø
n.177 (Sub Menu 1/6): Press six to increase audio
verification sensitivity.
Ø
n.164 (Menu 2): Press two for zone or partition status.
Ø
n.178 (Sub Menu 2/1): Press one then enter three
digit partition ID.
Ø
n.179 (Sub Menu 2/2): Press two then enter three
digit zone ID.
Ø
n.165 (Menu 3): Press three for output activation.
Ø
n.180 (Sub Menu 3/1): Enter two digit output ID then
press one for activation.
Ø
n.181 (Sub Menu 3/0): Enter two digit output ID then
press zero for deactivation.
Ø
n.166 (Menu 4): Press four to arm disarm panel.
Ø
n.182 (Sub Menu 4/1): Press one to arm away.
Ø
n.183 (Sub Menu 4/2): Press two to disarm.
Ø
n.184 (Sub Menu 4/3): Press three to arm stay type A.
Ø
n.185 (Sub Menu 4/4): Press four to arm stay type B.
Ø
n.186 (Sub Menu 4/5): Press five to arm stay type C.
Ø
n.187 (Sub Menu 4/6): Press six to arm stay type D.
Ø
n.167 (Menu 5): Press five to arm disarm partitions.
Ø
n.188 (Sub Menu 5/1): Enter two digit partition ID
then press one to arm away.
Ø
n.189 (Sub Menu 5/2): Enter two digit partition ID
then press two to disarm.
Ø
n.190 (Sub Menu 5/3): enter two digit partition ID
then press three to arm stay A.
Ø
n.191 (Sub Menu 5/4): Enter two digit partition ID
then press four to arm stay B.
Ø
n.168 (Menu 6): press six to enable disable installer.
Ø
n.192 (Sub Menu 6/1): Press one to enable installer.
Ø
n.193 (Sub Menu 6/0): Press zero to disable installer.
Ø
n.169 (Menu 7): Press seven to clear call queue.
Ø
n.170 (Mewhen a voice call is received from the Con-
trol Panelnu 8): Press eight to reset alarms.
Ø
n.171 (Menu 9): Press nine to disable code.
Ø
n.172 (Menu star): Press star to end call, pound for
main menu.
Messages from the No 159, to No. 193 of the Vocal Guide
have already recorded. The instructions of the recorded
vocal messages, and some examples of typical mes-
sages can be recorded by the installer.
+
If this option is disabled, the Control panel anyway
answer with voice messages to the status requests.
Default:
enabled.
DTMF Control
If this option is enabled, the user can
remotely manage the control panel, when a voice call is
received from the Control Panel, via a telephone that
support the DTMF tones (refer to “OPERATING THE
SYSTEM FROM A TELEPHONE” on the User Manual
for further information).
Default:
Enabled.
+
When the Control Panel is called, remote manage-
ment via a DTMF telephone is always possible if a
PIN enabled for this purpose is known.
+
Adjust the
Speaker Volume
and
Microphone Vol-
ume
on the GSM module (see the
GSM
option
group) to resolve any problems in managing the
control panel through the DTMF tones via the GSM.
Disable Siren for Audio Session
If during a audio
session (listen-in and/or two-way Talk) and the siren is ac-
tive, if this option is enabled (Yes), the siren will switch off.
Default:
No.
n
Advanced Call Options
Country Selection for tone setting
Select the coun-
try for the tone setting.
If the
Tone check
option is enabled (see
Phone op-
tions
) in this menu it is necessary to select the country
for the Tone setting: the values of the options
Fre-
quency Tone
,
Continuous
,
Tone Check
,
Tones
1-On
,
Tones 1-Off
,
Tones 2-On
,
Tones 2-Off
,
Tones
3-On
,
Tones 3-Off
for the Dial Tone, for the Congestion
Tone and the Busy Tone will be automatically
determined.
+
If a country is not on the list it is necessary to select
Custom
and set the options listed above.
n
EN50131/EN50136
e
In order to comply with the EN50131/EN50136
Standards, ALL the following options must be
ENABLED.
Refuse arming on incomplete exit condition
It
is
possible that the Control Panel is ready for arming also
whit open zones if these zones are programmed as
Exit
Delay
.
If this option is ENABLED, the Partitions are NOT
armed if there are zone still open at the end of the
Exit
Delay
.
Refuse arming on keyfob
If enabled, it is NOT possi-
ble to arm the Partitions using the keyfob in the pres-
ence of some of the block conditions (see “USER
MANUAL > APPENDIX> Arming block conditions”).
Apply EN50131 to Scheduler
If enabled, it is NOT
possible to arm the Partitions using the Scheduler in the
presence of some of the block conditions (see “USER
MANUAL > APPENDIX > Arming block conditions”).
Refused arming on Command Zones
If enabled, it
is NOT possible to arm the Partitions using the Com-
mand Zones in the presence of some of the block condi-
tions (see “USER MANUAL > APPENDIX > Arming
block conditions”).
Apply EN50131 to SMS Arming
If enabled, it is NOT
possible to arm the Partitions via SMS in the presence
of some of the block conditions (see “USER MANUAL >
APPENDIX > Arming block conditions”).
ABSOLUTA Plus
PROGRAMMING FROM THE PC
65
Содержание Bentel Security tyco ABS128M50
Страница 14: ...14 Expandable Hybrid Control Panel...
Страница 98: ...98 Expandable Hybrid Control Panel...
