Johnson & Starley HI-SPEC J40 Скачать руководство пользователя страница 11

11

LOW RATE

MEDIUM RATE

HIGH RATE

kW

MJ/h

Btu/h

kW

 MJ/h

Btu/h

kW

MJ/h

Btu/h

INPUT

11.75

42.35

40,100

13.5

48.58

46,050

15.18

54.65

51,800

OUTPUT

8.79

31.65

30,000

10.26

36.92

35,000

11.72

42.2

40,000

Gas rate cv

1.08m

3

/h (38.4ft

3

/h)

1.24m

3

/h (44.1ft

3

/h)

1.40m

3

/h (49.8ft

3

/h)

1037Btu/ft

3

Burner setting

9.2mbar (3.7 in wg)

12.2mbar (4.9 in wg)

16.0mbar (6.4 in wg)

pressure (hot)

Main Injector

BRAY CAT 23/1050

18

250

   300

     350

       400                 450 ft

3

/min

0.12

    0.14

      0.17

       0.19                0.21 m

3

/sec

                    AIR VOLUME

mbar in.wg.
0.625 0.25

0.50

0.20

0.375 0.15

0.25

0.10

0.125 0.05

RESIST

ANCE EXTERNAL

 T

O HEA

TER

170V

180V

190V

200V

210V

Table 4

Main Burner Pressure Settings

Table 5

Fan Performance Curve

7.

INSTRUCTIONS FOR USERS

7.1

If the building is unoccupied, ensure that the Instructions for User are left taped to the air heater for the User, and
Installation Instructions are left at or near the air heater for use on future service calls.

7.2

If the building is occupied, hand the User Instructions over and ensure the User understands:

7.2.1

How to ignite the pilot and burner.

7.2.2

How to operate the Thermista-stat/room thermostat, time and heater ON/OFF switch and summer air circulation
switch, and that the time control must be reset following a power failure.

7.2.3

How to extinguish the pilot and main burner at the Multifunctional control, and switch off the electrical supply to the
heater.

7.2.4

How to remove, clean and refit the air filter and at what intervals (i.e. fortnightly, or weekly for new houses).

7.2.5

How to control the heating system by opening and closing warm air outlets.

7.2.6

How to obtain summer air circulation.

7.2.7

That the air grilles on the heater or heater compartment; grilles and ventilators in the walls, windows or doors of the
building 

MUST NOT BE OBSTRUCTED

.

7.2.8

That the heater must be serviced at least once a year by a competent person to ensure efficient and safe operation.

DISCONNECT

TERMINALS ‘17’ &’18’

Y

N

REPLACE FAN DELAY

CONTROL/LIMIT

SWITCH

REPLACE

ELECTRONIC MOD-

ULE

FAN CONTINUES TO RUN, OR CYCLES AFTER HEATING IS TURNED OFF

DOES

FAN

RUN ?

MAIN BURNER NOT CYCLING

(

ROOM TEMPERATURE TOO HIGH)

REPLACE

MULTIFUNCTIONAL

CONTROL

N

Y

REPLACE

ELECTRONICS

MODULE

DISCONNECT

MULTIFUNCTIONAL

CONTROL AT

TERMINAL 15

N

DOES

BURNER

GO

OUT?

DISCONNECT

THERMISTA-STAT

REPLACE

THERMISTA-STAT

Y

DOES

BURNER

GO OUT?

Содержание HI-SPEC J40





























Отзывы: