Joab EcoDrive VL10U Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 57

background image

29

Tipping a Skip

The operator of the skip-loader is responsible for handling it. Care must be taken to
avoid injury or damage. Before operating the skip-loader make sure that you have
read and are fully aware of the warnings in this manual and on the skip-loader.

To tip a skip follow the procedure listed below. If tipping a skip with the use of the high-tipping-
chains, read and adhere to the information provided under

"High-Tipping-Chains", on page 37

before tipping the skip.

1.

Make sure that there is nobody within the
working area of the skip-loader.

2.

Lower the vehicle's axles.

3.

Turn the hydraulic pump ON. See

"Hydraulic Pump", on page 9

4.

Activate both the support-legs and lower
them. Verify that they are placed firmly
and secure on the ground.

If necessary, place supports under the
support legs so that they do not sink into
the ground.

NOTE:

See also

"Support Legs – Safety

Monitoring", on page 12

.

5.

Activate the tipping-hook and verify that it
engages with the skip correctly, as shown.

NOTE:

the tipping-hook is equipped with a

mechanical locking device. This is auto-
matically activated when the tipping-hook
makes contact with the skip's tipping-axle.

EcoDrive VL10-VL18 manual: 1021046 Edition 2 | 2022-05-02

«
...
33
34
35
36
37
...
»

Содержание EcoDrive VL10U


























































Отзывы:

Нет отзывов

Похожие инструкции для EcoDrive VL10U

Бренд: Eaton Страницы: 18

Cutler-Hammer IQ DP-4000

Бренд: Eaton Страницы: 87

Бренд: Jäger Страницы: 50

EcoTouch Ai1 Geo

Бренд: WATERKOTTE Страницы: 60

Бренд: WaterCop Страницы: 4

Бренд: Parkside Страницы: 113

Бренд: BlitzRotary Страницы: 41

Бренд: MAC TOOLS Страницы: 20

Бренд: Gude Страницы: 122

NVL Vista Series

Бренд: Braun Страницы: 53

Бренд: EC POWER Страницы: 62

DS-75D16 Swingarc

Бренд: Miller Electric Страницы: 48

Бренд: STAYER WELDING Страницы: 56

Taurus **5 Basic S Series

Бренд: EWM Страницы: 41

Бренд: Contec Страницы: 62

Бренд: Poweramp Страницы: 40

Бренд: SincoSald Страницы: 24

Бренд: Aerotech Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды