Joab EcoDrive LA Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 89

background image

69

Safety Warnings

The EcoDrive Hook-Lift has a number of safety labels attached to it, as shown below. It is
important to read and adhere to these warnings. Failure to do so can lead to serious injury or
damage to equipment.

Make sure that the labels are in good condition. If necessary, new safety labels can be ordered
from JOAB.

Safe Working Distance

Make sure that there are no unauthorised persons in close prox-
imity of the EcoDrive Hook-Lift's working area. The risk zone is
8 metres in all directions of the EcoDrive Hook-Lift and body.

Working on the Hook-Lift

Never work under a hook-lift without the use of the tip-supports.
Make sure that the body is removed from the hook-lift and that
the tip-supports are mounted correctly so that they support the
hook-lift, before carrying out any work.

Refer also to

"Working on the Hook-Lift", on page 66

Park the Hook-Lift before driving the Vehicle

Make sure the hook lift is parked before driving the vehicle. Fail-
ure to do so can lead to serious injury or damage. There is a ser-
ious risk that the hook will make contact with the environment if
it is not parked.

Risk of Slipping

Be aware when operating the hook-lift that there may be a risk of slipping, that
could lead to injury.

Suspended Loads

Do not stand or walk underneath a suspended load. If a suspended load
breaks free it can lead to serious injury or death.

EcoDrive 2.0 manual: 1021970 Edition 1 | 2022-02-04

«
...
75
76
77
78
79
...
»

Содержание EcoDrive LA


























































































Отзывы:

Нет отзывов

Похожие инструкции для EcoDrive LA

Бренд: Palfinger Страницы: 34

Бренд: GREER Company Страницы: 35

Бренд: STAYER WELDING Страницы: 56

Бренд: Barton Страницы: 36

Бренд: Mark Climate Страницы: 60

Бренд: M-system Страницы: 7

Hardon mini R1271C

Бренд: Caen RFID Страницы: 39

Бренд: PROCRAFT Страницы: 25

Бренд: Logic Страницы: 3

Бренд: INNO Instrument Страницы: 45

Бренд: Thermal Dynamics Страницы: 40

Бренд: M-system Страницы: 10

Бренд: TradeWeld Страницы: 11

Бренд: Velux Страницы: 24

Бренд: MESA Electronic Страницы: 19

Бренд: Lincoln Electric Страницы: 47

Бренд: iCONNECT Страницы: 20

Бренд: Air Liquide Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды