Joab EcoDrive LA Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 89

background image

Icon

Function

Start the continuous-hydraulic-supply. The power-take-of must be active.

Increase the continuous-hydraulic-supply

Decrease the continuous-hydraulic-supply

Stop the continuous-hydraulic-supply

Table 9: Hydraulic supply to tip trailer

Autocycle System - ACS

As an extra option, the cab controller can also be equipped with an automatic cycle function.
This is used to load or unload a body in one continuous cycle. The auto-cycle function has the
following procedures:

Auto-Cycle – Unload

1.

Open the hydraulic lock -

manually

.

2.

Extending-section is retracted.

3.

Hook-post is shunted all the way backwards

1

.

Auto-Cycle – Load

1.

The hook-post is fully lowered.

2.

The extending-section is fully extended

2

.

3.

The hydraulic-lock is locked.

To activate the unload cycle, keep the top button pressed and pull the control-stick backwards .
To activate the load cycle, keep the top button pressed and push the control-stick forwards.
See also

"Control Stick Function", on page 17

NOTE

1

: If PMS is installed and active, the hook-post will stop at the set PMS position.

NOTE

2

: If FFD is active, the body will raise slightly and then the extending-section will be exten-

ded. If CMS is installed and active, the extending-section will stop at the set CMS position.

Asphalt Driving Mode

Always verify that the extending-section functions correctly before using asphalt driv-
ing mode. Failure to do so can lead to damage or injury. Test and make sure that the
extending-section stops approximately 300 mm from the fully retracted position and
that it does not engage the centre-lock.

31

Operation | EcoDriveOptional Functions

EcoDrive 2.0 manual: 1021970 Edition 1 | 2022-02-04

«
...
37
38
39
40
41
...
»

Содержание EcoDrive LA


























































































Отзывы:

Нет отзывов

Похожие инструкции для EcoDrive LA

Бренд: Wayne-Dalton Страницы: 24

Бренд: Eaton Страницы: 18

Cutler-Hammer IQ DP-4000

Бренд: Eaton Страницы: 87

Бренд: Olimpia splendid Страницы: 40

Бренд: WAGO Страницы: 56

Бренд: YASKAWA SIEMENS Страницы: 373

Бренд: SanRex Страницы: 98

UTILITY UTAC13-0

Бренд: WIA Страницы: 8

Бренд: Nelson Страницы: 19

Бренд: Colorbeam Страницы: 12

NeverFreeze SX-0810-24

Бренд: ThermoSoft Страницы: 5

AXE 320 PULSE smart

Бренд: Alfain Страницы: 13

POWER WAVE AC/DC

Бренд: Lincoln Electric Страницы: 48

Бренд: Leviton Страницы: 2

I/O SYSTEM 750 750-635

Бренд: WAGO Страницы: 18

R7F4DC-DAC16D-H

Бренд: M-system Страницы: 8

BABYPACK 3246-N

Бренд: Dibipack Страницы: 39

Бренд: jbc Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды