manualshive.com logo in svg

JLG 680S, Руководство по обслуживанию и ремонту

JLG 680S – это мощная платформа с большой грузоподъемностью. Для обеспечения долговечности и безопасной эксплуатации необходимо регулярное обслуживание. Скачайте инструкцию по обслуживанию и ремонту бесплатно на manualshive.com и следуйте ей для сохранения высокой производительности вашего оборудования.

Поделиться
Скачать
background image

SECTION 3 - CHASSIS & TURNTABLE

3-24

3121234

Spindle Brake Sub-Assembly

NOTE:

Refer to Figure 3-17., Spindle Brake Sub-Assembly.

NOTE:

This procedure applies only to units with integral input
brake (2).

NOTE:

For this procedure, use the Brake Assembly Drawing (Figure
3-17.), which will show the proper balloon numbers for the
individual brake components. In the following instructions,
if the number has a “-” between two numbers, it refers to
the Brake Assembly Drawing only and NOT the Drive Hub
Assembly Drawing.

NOTE:

The Pressure Plug (12) requires a special tool for installa-
tion. It is not recommended to remove this plug unless it is
leaking. The plug is called a Koenig Expander. The installa-
tion tool is not supplied by Fairfield manufacturing, but
can be supplied by the manufacturer of the Koenig
Expander, Sherex Industries, or one of their distributors.

1.

Install Pressure Plug (12) into Spindle (1A) using follow-
ing procedure:

a.

Clean hole in spindle using appropriate Loctite
spray.

b.

Dip collar of plug in Loctite 290 or 680 (keep
unplugged portion of hole free of Loctite).

c.

Using appropriate tool, install plug flush with sur-
face of spindle.

SAFETY GLASSES MUST BE WORN DURING THE NEXT STEP.

2.

Place Spindle (1A) such that the splined end is facing
down. Using appropriate tool (See back of manual),
install Retaining Ring (2-1) into the spindle groove
within the splines.

3.

Place Washer (2-10) on top of Retaining Ring (2-1).

4.

Place Stator (2-9) on top of Washer (2-10).

5.

Place Rotor (2-12) on top of Stator (2-9).

6.

Repeat steps 3 & 4 until there are a total of 8 Stators (2-9)
and 7 Rotors (2-12) installed.

7.

Place Piston (2-8) such that the smaller O.D. end is facing
upward.

8.

Grease the large Backup Ring (2-3) and install in the
large-diameter groove at the bottom of the Piston (2-8).

9.

Grease the large O-Ring (2-2) and install in the large-
diameter  groove  at  the  bottom  of  the  Piston  (2-8),  on
top of the large Backup Ring (2-3).

10.

Grease the small O-Ring (2-5) and install in the small-
diameter groove near the top of the Piston (2-8). Make
sure the o-ring is seated on the bottom of the groove.

11.

Grease the small Backup Ring (2-4) and install in the
small-diameter groove near the top of the Piston (2-8),
on top of the small O-Ring (2-5).

NOTE:

If piston comes pre-assembled with shipping bolts (2-11),
skip to Step 15.

12.

Insert Piston (2-8) into Spindle (1A) until it contacts the
Stator (2-9).

13.

Insert the appropriate number of Springs (2-13) into Pis-
ton (2-8) counterbore. Use the brake spring chart below
and a bill of materials for your particular model number
to determine the number of springs.

14.

Place Pressure Plate (2-7) on top of Springs (2-13).

SAFETY GLASSES MUST BE WORN DURING THE NEXT TWO STEPS.

15.

Using snap ring pliers, install Retaining Ring (2-6) into
groove in Spindle (1A) and on top of Pressure Plate (2-7).
Make sure that Retaining Ring (2-6) is seated properly in
the groove.

16.

Remove Shipping Bolts (2-11) in brake pressure plate to
release springs in brake. Before removing bolts, use the
Coupling (9) (See Assembly Drawing at back of manual)
to center and align the Brake Rotors (2-12) with the Spin-
dle (1A).

BRAKE

CODE

BRAKE P/N

NUMBER

OF SPRINGS

A

902337

12

B

902341

10

C

902342

8

D

902343

6

E

902345

9

Содержание 680S



















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 680S

Jacka Industries JackaJay User Manual preview
JackaJay
Бренд: Jacka Industries Страницы: 24
IFM ANT600 Installation Instructions Manual preview
ANT600
Бренд: IFM Страницы: 13
PACH & COMPANY AeGIS 4000 Quick Installation And Programming Manual preview
AeGIS 4000
Бренд: PACH & COMPANY Страницы: 4
Panamax M4000-PRO Instructions Manual preview
M4000-PRO
Бренд: Panamax Страницы: 16
Measurement Computing CIO-DAS1401/12 User Manual preview
CIO-DAS1401/12
Бренд: Measurement Computing Страницы: 32
Telwin 823350 Instruction Manual preview
823350
Бренд: Telwin Страницы: 164
Mesa 7I76 Manual preview
7I76
Бренд: Mesa Страницы: 58
Castex QJY-S3 Manual preview
QJY-S3
Бренд: Castex Страницы: 23
Parweld XTS166 RC Operator'S Manual preview
XTS166 RC
Бренд: Parweld Страницы: 16
Parweld XTS 163 Operator'S Manual preview
XTS 163
Бренд: Parweld Страницы: 16
Balluff BNI PNT-507-005-Z040 Installation Manual preview
BNI PNT-507-005-Z040
Бренд: Balluff Страницы: 2
M-system Devicenet R7F4DD-DA16A-H Instruction Manual preview
Devicenet R7F4DD-DA16A-H
Бренд: M-system Страницы: 7
Elo Touch Solutions ET1523L User Manual preview
ET1523L
Бренд: Elo Touch Solutions Страницы: 3
Elko eLAN-RF-003 Instruction Manual preview
eLAN-RF-003
Бренд: Elko Страницы: 18
ITR OASIS NE-S Owner'S Manual preview
OASIS NE-S
Бренд: ITR Страницы: 15
Liko UltraTwin FreeSpan Instruction Manual preview
UltraTwin FreeSpan
Бренд: Liko Страницы: 10
Tokentools multi 164 Instruction Manual preview
multi 164
Бренд: Tokentools Страницы: 29
REID LIFTING PORTADAVIT QUANTUM PDQ 1 Assembly & Operation Manual preview
PORTADAVIT QUANTUM PDQ 1
Бренд: REID LIFTING Страницы: 17

Бренды по названию

Популярные бренды

Загрузить еще бренды