JLG 680S Скачать руководство пользователя страница 62 | Manualshive

Страница: 62 / 530

background image

SECTION 3 - CHASSIS & TURNTABLE

3-10

3121234

3.3

OSCILLATING AXLE LOCKOUT TEST
(IF EQUIPPED)

LOCKOUT SYSTEM TEST MUST BE PERFORMED QUARTERLY, ANY TIME A SYS-
TEM COMPONENT IS REPLACED, OR WHEN IMPROPER SYSTEM OPERATION IS
SUSPECTED.

NOTE:

Ensure boom is fully retracted, lowered, and centered
between drive wheels prior to beginning lockout cylinder
test.

1.

Place a 6 in. (15.2 cm) high block with ascension ramp in
front of left front wheel.

2.

From platform control station, start engine.

3.

Place DRIVE control lever to FORWARD position and
carefully drive machine up ascension ramp until left
front wheel is on top of block.

4.

Carefully activate SWING control lever and position
boom over right side of machine.

5.

With boom over right side of machine, place DRIVE con-
trol lever to REVERSE and drive machine off of block and
ramp.

6.

Have an assistant check to see that left front or right rear
wheel remains elevated in position off of ground.

7.

Carefully activate SWING control lever and return boom
to stowed position (centered between drive wheels).
When boom reaches center, stowed position, lockout
cylinders should release and allow wheel to rest on
ground, it may be necessary activate DRIVE to release
cylinders.

8.

Place the 6 in. (15.2 cm) high block with ascension ramp
in front of right front wheel.

9.

Place DRIVE control lever to FORWARD and carefully
drive machine up ascension ramp until right front wheel
is on top of block.

10.

With boom over left side of machine, place DRIVE con-
trol lever to REVERSE and drive machine off of block and
ramp.

11.

Have an assistant check to see that right front or left rear
wheel remains elevated in position off of ground.

12.

Carefully activate SWING control lever and return boom
to stowed position (centered between drive wheels).
When boom reaches center, stowed position, lockout
cylinders should release and allow wheel to rest on
ground, it may be necessary activate DRIVE to release
cylinders.

13.

If lockout cylinders do not function properly, have quali-
fied personnel correct the malfunction prior to any fur-
ther operation.

3.4

EMERGENCY TOWING

RUNAWAY VEHICLE/MACHINE HAZARD. MACHINE HAS NO TOWING BRAKES.
TOWING VEHICLE MUST BE ABLE TO CONTROL MACHINE AT ALL TIMES. ON-
HIGHWAY TOWING NOT PERMITTED. FAILURE TO FOLLOW INSTRUCTIONS
COULD CAUSE SERIOUS INJURY OR DEATH.
MAXIMUM TOWING SPEED 5 M.P.H. (8 K.M.H.)
MAXIMUM TOWING GRADE 25%.

DO NOT TOW MACHINE WITH ENGINE OPERATING OR DRIVE HUBS ENGAGED.

1.

Retract, lower and position boom in travel position; lock
turntable.

2.

Disconnect drive hubs by inverting disconnect cap.

3.

Reconnect the drive hubs by inverting the disconnect
cap when towing is complete.

Figure 3-7. Drive Disconnect Hub

«
...
60
61
62
63
64
...
»

Содержание 680S



















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 680S

Бренд: Magmaweld Страницы: 8

Бренд: Magmate Страницы: 20

Бренд: Magliner Страницы: 20

IntelliZone2 MasterStat

Бренд: Water Furnace Страницы: 44

Masterweld 204T

Бренд: AES Страницы: 31

Бренд: Ewellix Страницы: 18

Бренд: VENCO Страницы: 21

Бренд: Aichi Страницы: 54

Бренд: U-Line Страницы: 18

Бренд: EAE Страницы: 50

Бренд: ATEN Страницы: 176

AIR VANTAGE 500 CUMMINS

Бренд: Lincoln Electric Страницы: 51

Бренд: Pittsburgh Страницы: 12

iO-GRID M GFDO-RM01N

Бренд: DAUDIN Страницы: 25

Бренд: A-T Controls Страницы: 19

Бренд: ESAB Страницы: 45

Бренд: SPINOGY Страницы: 27

R7G4FML3-6-DA16

Бренд: M-system Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды