JLG 530LRT, Руководство по обслуживанию и ремонту

Страница: 127 / 262

SECTION 4 - BASIC HYDRAULIC INFORMATION & SCHEMATICS
3121781 4-17
Assembly Instructions for O-ring Face Seal (ORFS)
Fittings
1. Ensure proper o-ring is installed. If o-ring is missing
install per O-ring Installation (Replacement).
2. Ensure surface is smooth, free of rust, weld and brazing
splatter, splits, dirt, foreign matter, or burrs. If necessary
replace fitting or adapter.
CARE TO BE TAKEN WHEN LUBRICATING O-RING. AVOID ADDING OIL TO THE
THREADED CONNECTION OF THE FITTING. THE LUBRICATION WOULD CAUSE
INCREASED CLAMPING FORCE AND CAUSE FITTING DAMAGE.
3. Pre-lubricate the o-ring with Hydraulic Oil.
4. Place the tube assembly against the fitting body so that
the flat face comes in contact with the o-ring. Hand
thread the nut onto the fitting body.
5. Torque nut to value listed in Table 4-7, O-ring Face Seal
(ORFS) - Steel or Table 4-8, O-ring Face Seal (ORFS) - Alu-
minum/Brass while using the Double Wrench Method.
Refer to FFWR and TFFT Methods for procedure require-
ments if using the FFWR method.
NOTE: Torque values provided in Table 4-7, O-ring Face Seal
(ORFS) - Steel and Table 4-8, O-ring Face Seal (ORFS) - Alu-
minum/Brass are segregated based on the material config-
uration of the connection.
ALUMINUM/BRASS FITTINGS OR ALUMINUM/BRASS MATING
COMPONENTS’ indicate either the following material configu-
rations:
• STEEL fittings with ALUMINUM or BRASS mating compo-
nents
• ALUMINUM or BRASS fittings with STEEL mating compo-
nents
• ALUMINUM or BRASS fittings with ALUMINUM or
BRASS mating components
Table 4-7. O-ring Face Seal (ORFS) - Steel
TYPE/FITTING IDENTIFICATION Torque
Flats from Wrench
Resistance (F.F.W.R)**
MA
TERIAL
Dash Size
Thread Size ØA* ØB* [ft. lb.] [N-m]
Tube Nuts
Swivel &
Hose Ends
(UNF) (in) (mm) (in) (mm) Min Nom Max Min Nom Max
ST
EE
L F
ITT
IN
GS
W
IT
H
ST
EE
L M
AT
ING
C
OMP
ON
EN
TS
;
UN
-L
UBRIC
ATED THRE
ADS
4 9/16-18 0.51 13.00 0.56 14.20 18 19 20 25 26 27 1/4 to 1/2 1/2 to 3/4
6 11/16-16 0.63 15.90 0.69 17.50 30 32 33 40 43 45 1/4 to 1/2 1/2 to 3/4
8 13/16-16 0.75 19.10 0.81 20.60 40 42 44 55 57 60 1/4 to 1/2 1/2 to 3/4
10 1-14 0.94 23.80 1.00 25.40 60 63 66 81 85 89 1/4 to 1/2 1/2 to 3/4
12 1 3/16-12 1.11 28.20 1.19 30.10 85 90 94 115 122 127 1/4 to 1/2 1/2 to 3/4
16 1 7/16-12 1.34 34.15 1.44 36.50 110 116 121 149 157 164 1/4 to 1/2 1/2 to 3/4
20 111/16-12 1.59 40.50 1.69 42.90 150 158 165 203 214 224 1/4 to 1/2 1/2 to 3/4
24 2-12 1.92 48.80 2.00 50.80 230 242 253 312 328 343 1/4 to 1/2 1/2 to 3/4
32 2 1/2-12 2.43 61.67 2.50 63.50 375 394 413 508 534 560 1/4 to 1/2 1/2 to 3/4
* ØA and ØB thread dimensions for reference only.
** See FFWR and TFFT Methodsfor FFWR procedure requirements.