manualshive.com logo in svg

JLG 25RTS, Обслуживание и техническое обслуживание, Страница: 57 / 84

Поделиться
Скачать
JLG 25RTS Скачать руководство пользователя страница 57

SECTION 2 - PROCEDURES

3120826

– JLG Sizzor –

2-41

2.26 DRIVE BRAKE - 2WD/2WS REAR

Disassembly

1.

Remove end cover from housing by removing
washer head cap screws.

END COVER IS UNDER SPRING TENSION OF APPROXIMATELY
2000 LBS. (907 KG.) THE FOUR WASHER HEAD CAP SCREWS
SHOULD BE LOOSENED EVENLY TO RELIEVE THIS FORCE. IF A
HYDRAULIC PRESS IS AVAILABLE 3000 LBS. MIN. (1361 KG MINI-
MUM), COVER CAN BE HELD IN POSITION WHILE REMOVING
WASHER HEAD CAP SCREWS.

2.

Remove  case  seal  from  housing,  then  remove
bleeder screw from end cover.

3.

Remove piston from end cover.

4.

Remove o-ring, back-up ring, o-ring and back-up
ring from piston.

5.

Remove separators from housing.

6.

Remove stack assembly, consisting of discs, return
plate, and friction discs from housing.

7.

Remove dowel pins, springs (5 & 6), and spring
retainer from housing.

NOTE: Not all models use the same number of springs or

spring pattern. Record this information for assembly
purposes.

8.

Remove retaining ring from housing.

9.

Remove shaft by pressing or using a soft mallet on
male end of shaft.

10.

Remove retaining ring and bearing from shaft.

11.

Press rotary oil seal from housing.

Assembly

NOTE: Lubricate all rubber components from repair kit with

clean hydraulic fluid of the type used in the system.

1.

Clean all parts thoroughly before assembly.

2.

Press new rotary oil seal into housing. Note direction
of seal.

3.

Install new bearing and retaining ring on shaft .

4.

Insert shaft assembly and retaining ring in housing.

5.

Insert dowel pins, spring retainer, and springs (5 &
6) in housing

Содержание 25RTS





















































































Отзывы:

Нет отзывов