SB-H-RIDGLNE/10W3v3_ 011214
STEALTHBOX WALL
THREADED INSERT
VEHICLE SHEET METAL
FENDER WASHER
SOCKET CUP SET SCREW
LOCK WASHER
FLAT WASHER
HEX NUT
C O N G R A T U L A T I O N S
You have completed the installation for this model!
Please refer to the Power Recommendation section for an
amplifier recommendation and basic set-up help.
S T E P 6
From under the vehicle, place the supplied fender washer,
flat washer, lock washer and then hex nut onto the protrud-
ing socket cup set screw. Secure tightly with a 14mm socket,
long extension and rachet.
Note: For added protection it is recommended that
you apply a bead of silicone between the vehicle and
the fender washer. After the bolt assembly is tightly
secured, it is also recommended that vehicle under-
coating material is applied to the exposed assembly.
S T E P 5
(A)
Loosen the socket cup set screw to expose 1-1/2-inch.
Place the enclosure into place, carfully guiding the socket
cup set screw through the drilled hole. .
(B)
Run speaker wire from the amplifier location to the
Stealthbox® and attach to the terminal
Double check the woofer for proper operation.
S T E P 4
(A)
Posistion the Stealthbox® into place and press firmly
down. This is to make an impression onto the wax square.
Remove the Stealthbox®.
(B)
With a 1/2" drill bit or StepBit/Unibit® and drill. Drill at the
impression on the wax square, through the metal floor to the
outside.
(C)
Remove the wax sqaure.
Page 2 • JL Audio, Inc 2006
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered
trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.
JLA-SKU#011214-07-2006
• Printed in USA • ©2006 JL Audio, Inc. • U.S. PATENTS: #5,734,734 #5,949,898 #6,118,884 #6,229,902 #6,243,479
#6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign patents pending.
For more detailed information please visit us online at
www.jlaudio.com.
(954) 443-1100
w w w . j l a u d i o . c o m
1 0 3 6 9 N O R T H C O M M E R C E P A R K W A Y • M I R A M A R , F L O R I D A • 3 3 0 2 5 • U S A
I N C L U D E D H A R D W A R E
(1)
3/8-inch - 16 Hex Nut
(1)
3-inch x 3-inch Wax Square
(1)
3/8-inch x 3/4-inch USS Flat Washer
(1)
3/8-inch - 16 x 2-1/4-inch Socket Cup Screw
(1)
3/8-inch x 1-1/4-inch Fender Washer
(1)
3/8-inch Lock Washer
S P E C I F I C A T I O N S
Enclosure Type:
Acoustic Suspension (sealed)
Driver Type:
10W3v3-4
Nominal Impedance:
4 ohms mono
Continuous Power Handling:
300 Watts
P O W E R R E C O M E N D A T I O N
JL Audio recommends using a high quality amplifier such as the JL Audio 250/1.
The diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the 250/1 when
being used to power your Stealthbox
®
.
JL AUDIO
250/1
monoblock subwoofer amplifier
Amplifier Input Section
Input Sens.
Input Voltage
Low/High
Left Ch.
Right Ch.
Signal Sensing
Off/On
Output Mode
Full-Range/Low-Pass/High-Pass
Left Ch.
Right Ch.
Amp LP Filter
Mode/Slope
Off/12dB/24dB
Filter Freq. (Hz)
Bass Control
LF Boost (dB)
Off/30Hz
Infrasonic Filter
+1
+13
+3
+7
+10
Preamp Output Section
+12VDC
Ground
Remote
The JL Audio 250/1 is a very versatile audio component. Please consult the owner’s manual for even more
detailed information about installing and tuning this amplifier.
M I D / H I G H F R E Q U E N C Y D R I V E R F I T M E N T
A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.
Front Speaker Size / Location:
6.5-inch / Front Doors
Fits JL Audio Models:
TR650-CXi, VR650-CSi, VR650-CXi, XR650-CSi, XR650-CXi & ZR650-CSi
Rear Speaker Size / Location:
6.5-inch / Rear Deck
Fits JL Audio Models:
TR650-CXi, VR650-CXi & XR650-CXi
