background image

14

 

JL Audio

 

 

 

 

15

“my amplifier turns on, but there is no output”

 

Check  

the input signal using an AC voltmeter to measure the 
voltage from the source unit while an appropriate test tone is 
played through the source unit (disconnect the input cables 
from the amplifier prior to this test). The frequency used 
should be in the range that is to be amplified by the amplifier  
(example: 50 Hz for a sub bass application or 1 kHz for a full 
range / high-pass application).  A steady, sufficient voltage 
(between 0.2 and 8.0-volts) should be present at the output of 
the signal cables. 

 

Check  

the output of the amplifier. Using the procedure explained in 
the previous check item (after plugging the input cables back 
into the amplifier) test for output at the speaker outputs of 
the amplifier. Unless you enjoy test tones at high levels, it is 
a good idea to remove the speaker wires from the amplifier 
while doing this.  Turn the volume up approximately half 
way. 5V or more should be measured at the speaker outputs.  
This output level can vary greatly between amplifiers but it 
should not be in the millivolt range with the source unit at 
half volume. If you are reading sufficient voltage, check your 
speaker connections as explained below.

 

Check

  to ensure that the speaker wires are making a good 

connection with the metal inside the terminal block.  The 
speaker wire connectors are designed to accept up to 8 AWG 
wire.  Make sure to strip the wire to allow for a sufficient 
connection with the metal inside the terminal block.

“How do i properly set the input sensitivity on my amplifier”

 

Please  

refer to Appeaset the input sensitivity for maximum, low-
distortion output.

“my amplifier doesn’t turn on”

 

Check  

the fuse, not just visually, but with a continuity meter. It is 
possible for a fuse to have poor internal connections that 
cannot be found by visual inspection. It is best to take the 
fuse out of the holder for testing. If no problem is found with 
the fuse, inspect the fuse-holder. 

 

Check  

the integrity of the connections made to each of the 

+12VDC

”,  “

Ground

”,  and “

Remote

” terminals. Ensure 

that no wire insulation is pinched by the terminal set screw 
and that each connection is tight. 

 

Check  

to make sure there is +12V at the

 “Remote”

 connection of the 

amplifier. In some cases, the turn-on lead from the source unit 
is insufficient to turn on multiple devices and the use of a relay 
is required.  To test for this problem, jump the “

+12VDC

” wire 

to the “

Remote

” terminal to see if the amplifier turns on. If this 

does not work, proceed to the next step.

 

“my amplifier’s output fluctuates when i tap on it or hit a bump”

 

Check  

the connections to the amplifier. Make sure that the 
insulation for all wires has been stripped back far enough to 
allow a good contact area inside the terminal block. 

 

Check  

the input connectors to ensure that they all are making good 
contact with the input jacks on the amplifier. 

aPPendix C:  troublesHooting

Содержание J2360.2












Отзывы: