manualshive.com logo in svg

Jinko Solar JKM M-60 Plus Series, Руководство по установке

Поделиться
Скачать
Jinko Solar JKM M-60 Plus Series Скачать руководство пользователя страница 7

 
 
 

 

 

-7- 

2.3.2 Fixation with clamps 

The module clamps should not come into contact with the front glass and must not deform the 

frame. Be sure to avoid shadowing effects from the module clamps. The module frame is not to 

be  modified  under  any  circumstances.  When  choosing  this  type  of  clamp-mounting  method, 

please be sure to use at least four clamps on each module, two clamps should be attached on 

each  long  sides  of  the  module.  Depending  on  the  local  wind  and  snow  loads,  if  excessive 

pressure load is expected, additional clamps or support would be required to ensure the module 

can bear the load. The applied torque value should be big enough to fix the modules steadily 

(Please consult 

with the clamp or support’s supplier for the specific torque value). Please find 

detailed  mounting  information  in  the  below  illustration,  the  mounting  place  distance  is 

suggested bigger than J and less than K.

 

The installation diagram of clamp is shown in figure 3.   

Note: The Movement of the mounting rail and the clamps center line are recommended to be 

within the black arrow area. 

When  installing  modules  using  clamps  on  the  long  side  of  the  frame,  the  applicable  product 

types and installation locations are shown in figure 4 and table 2.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 3: PV module installed at the side with Clamp fitting method 

Middle modules installation

 

Fringe modules installation

 

Содержание JKM M-60 Plus Series



















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды