manualshive.com logo in svg

Jide CARINO 67, Руководство по установке, использованию и обслуживанию

Поделиться
Скачать
Jide CARINO 67 Скачать руководство пользователя страница 14

Jidé s.a. – Rue des Meuneries 11 – B-4650 HERVE (Belgique) – Tél. +32 87 31.75.12 – Fax +32 87 31.75.11 – 

www.jide.be

 - 

[email protected]

 

 

CARINO (EN)   February 2020 

 

 

14 

7.

 

Security or automatic stop 
 

The insert can stop working automatically and for security in three different cases: 

-

 

Pilot security: when the flame of the pilot lights up, it heats a thermocouple of security. If this 
one is not heated anymore, the device will turn off automatically (see malfunction tables at 
the end of the manual). 

-

 

Temperature security: in order to avoid overheating of electric components, the receptor  is 
fitted with a sensor which will stop the device if the temperature in the box reaches 60° C (see 
malfunction tables at the end of the manual). 

-

 

Low battery in the receptor turns the device in security mode. Replace the battery. 

 
8.

 

Convection ventilation 

 
This insert is fitted with two integrated fans which spread the warm convection air in the room from 
the top of the door or from warm air ducts previously installed. The start and stop of the fans is done 
automatically  by  a  thermal  switch  (airstat).  The  speed  setting  is  done  by  the  speed  controller 
supplied with the device. 
 
Attention: 
 
-

 

The device can NOT work without ventilation. It is necessary to cool down the fireplace, its 
electrical components and its trim. In case of malfunction, contact your installer. 

-

 

Do not use another speed controller than the one supplied with the insert. 

 
9.

 

Maintenance 

 
9.1

 

 Regular maintenance 

 

-

 

Outside cleaning of the glass 

When the glass is dirty on the outside, it is important to clean it by means of a cleaning product for 
glass or of vinegared water. 
Every biting products are to ban at risk of deteriorating the front painting or the ceramic protection. 
Use a soft cloth. If the glass has dirt stuck on it, use a razor blade or a scraper for glass-ceramic. 

 

Note: If a dirt is not previously removed before starting a fire, it could became permanent (cooked 
in the ceramic)! 
 
-

 

External cleaning of the fireplace 

Dust the accessible zones around the fireplace by means of a dry soft cloth and a feather duster, 
mainly on top of the insert. 
 
Note: when the device is not used for a long time, dust settles on the heating chamber. During the 
first firing, an odour can appear due to the cooking of these residues. 
 

 

Содержание CARINO 67

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды