JGR OA1 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 32

background image

OA1 User Manual

21

M-OA1-001-01

:STATus:OPERation:ENABle?
:STATus:OPERation[:EVENt]?
:STATus:QUEStionable:CONDition?
:STATus:QUEStionable:ENABle <byte>
:STATus:QUEStionable:ENABle?
:STATus:QUEStionable[:EVENt]?
:STATus:PRESet
:SYSTem:ERRor[:NEXT]?
:SYSTem:VERSion?
:SYSTem:COMMunicate:LAN:ADDRess <ip/dhcp>
:SYSTem:COMMunicate:LAN:ADDRess?
:SYSTem:COMMunicate:LAN:GATEway <gateway>
:SYSTem:COMMunicate:LAN:GATEway?
:SYSTem:COMMunicate:LAN:MASK <netmask>
:SYSTem:COMMunicate:LAN:MASK?
:SYSTem:COMMunicate:LAN:HOSTname <hostname>
:SYSTem:COMMunicate:LAN:HOSTname?
:SYSTem:COMMunicate:LAN:MAC?

Note: for a single module OA1, omit [n] in the commands below.

Table 6: OA1 commands list

Command

Description

INput[n]:ATTenuation #

Attenuates <#> dB on module <n>.

INput:ATTenuation:ALL #

Attenuates <#> db on all modules that support it. If any modules

don’t support this, returns an error.

INput[n]:ATTenuation?

Returns the current attenuation on module <n>.

INput[n]:OFFSet #

Sets an attenuation offset <#> dB on module <n>. The offset only
affects the displayed attenuation value, not the actual attenuation.
ATT

display

= ATT

actual

+ Offset.

INput[n]:WAVelength <#>

Sets the wavelength <#> on module <n>.

INput[n]:WAVelength?

Returns the current wavelength on module <n>.

INput[n]:ILMin

Goes to the min IL point on module <n>.

OUTput[n]:APMode #

Sets the absolute power mode on module <n>: <1> (enabled) or <0>
(disabled).

OUTput[n]:POWer #

Sets the desired setpoint <#> in dBm mode on module <n>.

OUTput[n]:POWer?

Returns the setpoint in dBm mode on module <n>.

OUTput[n]:OFFset #

Sets the power offset <#> in dBm mode on module <n>.

LCL #

Sets the interaction mode <#> (1 = local, 0 = remote).

LCL?

Returns the interaction mode.

OUTput[n]:TRACKing #

Sets the power levelling setting <#> in dBm mode (1 = enabled, 0 =
disabled).

«
...
24
25
26
27
28
...
»

Содержание OA1

































Отзывы:

Нет отзывов

Похожие инструкции для OA1

Бренд: ABB Страницы: 6

Бренд: Odom Страницы: 19

Бренд: MacDon Страницы: 30

Бренд: idiag Страницы: 10

Бренд: Bandit Страницы: 136

Versaflo S Series

Бренд: 3M Страницы: 11

DBI Sala EXOFIT

Бренд: 3M Страницы: 32

Бренд: 3M Страницы: 8

Бренд: Accurate Bio-Medical Technology Страницы: 35

Бренд: Gaspardo Страницы: 16

Бренд: Gastrodomus Страницы: 4

Бренд: HANYOUNG NUX Страницы: 2

Бренд: Gastrodomus Страницы: 39

Бренд: MagCore Страницы: 80

Бренд: MagCore Страницы: 80

Бренд: Zodiac Страницы: 2

Бренд: Zipper Mowers Страницы: 37

Бренд: Zimmer Страницы: 46

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды