JETWAY MM21 Series Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 42

JETWAY MM21 Series Скачать руководство пользователя страница 32

28

following sub-items shall appear:

WatchDog Reset Timer Value

User can select a value in the range of [4] to [255] seconds when ‘WatchDog
Reset Timer Unit’ set as [Sec]; or in the range of [4] to [255] minutes when
‘WatchDog Reset Timer Unit’ set as [Min].

WatchDog Reset Timer Unit

The optional settings: [Sec.]; [Min.].

ATX Power Emulate AT Power

This item support Emulate AT power function, MB power On/Off control by power
supply. Use needs to select ‘AT or ATX Mode’ on MB jumper at first (refer to
JAT_ATX jumper setting Pin 1&2 of for ATX Mode & Pin 2&3 of AT Mode Select).

Case Open Detect

Use this item to detect case has already open or not, show message in POST.
The optional settings: [Disabled]; [Enabled].
When set as [Enabled], system will detect if COPEN has been short or not (

refer to

COPEN

jumper setting for Case Open Detection

); if Pin 1&2 of

COPEN

are short,

system will show Case Open Message during POST.



PC Health Status

Press [Enter] to view current hardware health status, make further settings in
‘

SmartFAN Configuration

’ and set value in ‘

Shutdown Temperature

’.

►

SmartFAN Configuration

Press [Enter] to make settings for

‘

SmartFan Configuration

’:

SmartFAN Configuration

CPUFAN1 / SYSFAN1 / SYSFAN2 Smart Mode

The optional settings: [Disabled]; [Enabled].

When set as [Enabled], the following sub-items shall appear:

CPUFAN1 / SYSFAN1 / SYSFAN2 Full-Speed Temperature

Use this item to set CPUFAN/SYSFAN full speed temperature. Fan will run at full
speed when above this pre-set temperature.

CPUFAN1 / SYSFAN1 / SYSFAN2 Full-Speed Duty

Use this item to set CPUFAN/SYSFAN full-speed duty. Fan will run at full speed
when above this pre-set duty.

CPUFAN1 / SYSFAN1 / SYSFAN2 Idle-Speed Temperature

Use this item to set CPUFAN /SYSFAN idle speed temperature. Fan will run at idle
speed when below this pre-set temperature.

CPUFAN1 / SYSFAN1 / SYSFAN2 Idle-Speed Duty

Use this item to set CPUFAN/SYSFAN idle speed duty. Fan will run at idle speed
when below this pre-set duty.



Second Super IO Configuration

Press [Enter] to view current hardware health status, make further settings in
‘

SmartFAN Configuration

’ and set value in ‘

Shutdown Temperature

’.

►

SmartFAN Configuration

Press [Enter] to make settings for

‘

SmartFAN Configuration

’:

SmartFAN Configuration

«
...
30
31
32
33
34
...
»

Содержание MM21 Series











































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды