Jetting V0 HD 18 V Скачать руководство пользователя страница 13

Страница: 13 / 16

9. Maintenance

Procedure

Daily

Weekly

Monthly

60 days

90 days

Clean all assemblies and components
thoroughly with dry cloth

If used in moisture weather. Remove the

machine from the transport box and leave
it to dry completely

Check/charge batteries in original charger

Inspect fasteners and screws

Check wheels for wear. Replace if excess wear

has occurred. Excessive wear has occurred
when the wheels are no longer able to
e

ectively grip the fiber optic

Duct pack seal replacement

Change rubber rings on drive wheel

Every 50 km unless excessive wear is occurring

Seals replacement

Every 10 km unless excessive wear is occurring

Wheel cleaning and tightening

Inspect wheel and tighten before and after each use. Clean after each
use, or when necessary

Disconnect power supply and exhaust any air pressure

before servicing any component on the V0 HD.

Avoid handling leaking couplings, valve seal or
inadequately sealed pipe in air block.

DANGER! Risk of air under pressure penetrating skin.

D A R E T O D O I T D I F F E R E N T L Y .

Содержание V0 HD 18 V

















Результаты поиска

Содержание V0 HD 18 V

Отзывы:

Бренды по названию

Популярные бренды

Jetting V0 HD 18 V, Руководство пользователя и инструкция по безопасности

Результаты поиска

Содержание V0 HD 18 V

Отзывы:

Бренды по названию

Популярные бренды