background image

6

MAINTENANCE PRECAUTIONS 

For all maintenance repairs and needs beyond the capability of the consumer, which may include but not be limited to: such 

as proper maintenance of brakes, control cables, bearing adjustments, wheel adjustments, lubrication, reflectors, tires and 

handlebar and seat adjustments, please contact the Jetson Care Team for assistance at: 

ridejetson.com/support 

US & Canada 1-(888) 976-9904 

DISPOSAL OF USED BATTERY

Battery may contain hazardous substances which could endanger the environment and human health. This 

symbol marked on the battery and/or packaging indicates that used battery shall not be treated as municipal 

waste. Batteries should be disposed of at an appropriate collection point for recycling. By ensuring the used batteries are 

disposed of correctly, you will help prevent potential negative consequences for the environment and human health. The 

recycling of materials will help to conserve natural resources. For more information about recycling of used batteries, 

please contact your local municipality waste disposal service. 

NOTICE OF COMPLIANCE

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not 

cause harmful interference, and (2) this device must accept any interference received, including interference that may cause 

undesired operation. 

WARNING:

 

Changes or modifications to this unit not expressly approved by the party responsible for compliance could void 

the user’s authority to operate the equipment.

NOTE:

 

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 

of the FCC Rules.  These limits are designed to provide reasonable protection against harmful interference in a residential 

installation.  This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in 

accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee 

that interference will not occur in a particular installation.  If this equipment does cause harmful interference to radio or 

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the 

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Shielded cables must be used with this unit to ensure compliance with the Class B FCC limits.

FCC ID:

 

California Proposition 65

      

WARNING

:

  

This product can expose you to a chemical such as Cadmium that is known to the state of California to cause cancer or birth 

defects or other reproductive harm. For more information go to www.p65warnings.ca.gov/product

Содержание Safara





























































Отзывы: