manualshive.com logo in svg

Jetmaster MK6, Инструкция по установке и эксплуатации

Поделиться
Скачать
Jetmaster MK6 Скачать руководство пользователя страница 26

27 

Dummy Switch 

Safety Off Switch 

Battery Lead 

Oxypilot Connections 

Oxypilot 

Sensor 

Valve 

Ignition Lead 

-  Pull EDB attached to heat shield forward out of the burner. 
-  Remove all the Connections from the EDB for ignition lead, thermocouple, valve, infrared sen-

sor, battery and dummy switch. 

-  The EDB can now be removed from the heat shield by removing the 4 nuts. 
-  The 8 spacer nuts and screws can now be removed from the EDB. 
- 

Note - The 8 spacer nuts and screws must be fitted to the replacement EDB to ensure 
that it is spaced away from the heat shield.

 

-  Re-assemble in reverse order ensuring all connectors are correctly fitted. 
-  Ensure pilot shield is correctly located. 

- 

Ensure remote infrared sensor correctly located and operating. If in doubt refer to section on 
positioning the sensor. 

Remote Control Sensor 

    The Sensor can be removed without disconnecting the gas supply or removing the EDB. 
-  Remove the sensor mounting screw and P clip. 
-  Disconnect the battery by pulling apart the plastic connector situated along the battery lead.  
-  Remove the battery. 
-  Remove the 2 screws holding the front panel. Remove panel. 
-  Remove sensor by pulling connector out of the EDB. 
-  Replace sensor and re-assemble in reverse order. 

Remote Control Safety Switch, Dummy Switch and Ignition Lead Replacement 

    The above can be removed without disconnecting the gas supply. 
-  Follow section on Remote Control EDB Box Replacement. 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fig. 17 

Содержание MK6































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды