MVario EX
-
2
-
Climb sens.
–
Set up of the sensor ascend sensitivity. If passing this threshold of ascend speed one segment of the
indicator in the sensor introduction display becomes filled up, and at the same time an acoustic signal reports that
the first stage of ascend speed has been achieved. For example: As long as this value will be set up to 0.5m all
segments of the indicator will become filled up, at the same time an acoustic signal will report achievement of the
last stage of 2m/s ascend velocity.
Descent sens. -
Set up of the sensor descend sensitivity. If passing this threshold of descend speed one segment
of the indicator in the sensor introduction display becomes filled up, and at the same time an acoustic signal reports
that the first stage of descend speed has been achieved. For example: As long as this value will be set up to -2,0m
all segments of the indicator will become filled up, at the same time an acoustic signal will report achievement of
the last stage of -8m/s descend velocity.
Beep period
– adjustment of the time between a group of tones of the Vario acoustic signals. The number of tones
corresponds with the change of climb rate/descent rate which has occured during the set time.
Trigger level
– adjustment of the value of the input pulse length, after whose exceeding the extremes become
deleted and the acoustic signalling of the climb rate/descent rate starts. As long as the MVario input is not
connected to the receiver channel the acoustic signalling is switched on constantly and deleting of extremes does
not proceed automatically. (We recommend connection of the input to the receiver channel which is controlled from
the transmitter by a switch or by the throttle channel.)
Reverse
– reversation adjustment of the input signal evaluation. (For instance, as long as the trigger level „Trigger
level“ is set to 1.50 ms and „Reverse“ to OFF). MVario evaluates an infringement if the input signal is longer than
1.50 ms and an automatic deletion of extremes occurs. Furthermore, extremes recording starts and acoustic
signalling of the Vario will be switched on. If the input signal lies below the trigger level, no recording of extremes
will occur and signalling is switched off.)
Alti. above sea
– adjustment of the reference altitude above sea level for sensor calibration. For exact
measurements of the absolute altidude the known altitude above sea level must be set at a point, where the sensor
will be operating further on.
Beep Vario Alarm
– adjustment of the Morse alphabet character which will represent infringement of the Vario alert
setting by an acoustical tone of the DUPLEX Tx transmitter module.
Beep Alti. Alarm
– adjustment of the Morse alphabet character which will represent infringement of the altidude
alert setting by an acoustical tone of the DUPLEX Tx transmitter module
Vario beep
– adjustment of one of 4 modes of the Vario acoustic signalling.
„ON“
is the active signalling of climb
and descent flight.
„ON – DESCENT“
is the active acoustic signalling for descent flight only.
„ON – CLIMB“
is the
active acoustic signalling for climb flight only. In the
„OFF“
mode the Vario acoustic signalling is switched off. These
adjustments do not affect the acoustical alert signalling which is always switched on. (If you want to be informed
about violation of one set alert only, signalling of the vario must be switched off. We do not recommend
simultaneous setting of alerts as well as signalling of the Vario.)
MVARIO MENU:
ALARMS
–
by pushing the button D (downward arrow) you will change to the setup of particular
alerts. If an adjusted parameter becomes passed over, the LCD screen of the JETIBOX will show in the second line
of the introduction screen alternately the original data with the matching alert and the buzzer of the transmitter
module will emit the alert signal. The first tone is the revelation tone and the second one beeps the Morse code of
the chacter representing the corresponding alert. If the alert is in position OFF, the given alert is switched off.
Vario High Al.
– adjustment of the signal representing high climb rate, if the value measured by the Vario exceeds
the set value, the alert will be activated.
Vario low Al.
- adjustment of the signal representing high descent rate, if the value measured by the Vario exceeds
the set value, the alert will be activated.
Alti. High Al.
- adjustment of the signal representing the relative altitude, if the value of the relative altitude exceeds
the set value, the alert will be activated
MVARIO MENU
:
SERVICE
– by pressing button D (arrow down) you will change to depiction of the firmware
version and to renewal of the sensor default setting.
Factory Defaults
– by simultaneous pressing of arrows R and L (right and left) the factory settings of the MVARIO
are loaded.
MVARIO v. xx.xx ID xxxxx:xxxxx
– product marking with firmware version and series number (ID).
Connecting the MVario
The MVario comprises an
exit
marked Ext. (
black connector
) and an
input
(
red connector
). Via the
exit
(
black
connector
) of the sensor informations are transmitted to the receiver or to the JETIBOX, and it serves as current
