Jet XACTA Скачать руководство пользователя страница 9

 

Wooden Extension Table 

The 

wooden extension table 

is an optional 

accessory. 

Tools required 

Electric drill 
Cross point screwdriver 
7/16" and 1/2" wrenches 
Four clamps 
Straight edge 
Hammer (or rubber mallet) 

Installation 

The optional wood extension table (including the 
optional router table) sits flush against the saw 
table and along the inside of the rails. The JET 
logo (or warning label on the router table) should 
face outward.  The extension table is not bolted to 
the saw table, it is bolted only to the rails. 

The extension table and saw table must be aligned 
properly so the XACTA Fence II will slide smoothly 
from one to the other.   

1.  Place the extension table between the rails 

and up against the saw table, leaving the 
extension table raised just slightly above the 
saw table.  Clamp the extension table to the 
front and back rails as shown in Figure 7.  
Clamping pressure should be enough to 
secure the table yet allow minor adjustments. 

2.  Use a hammer and block of wood (or a rubber 

mallet) to tap the extension table up flush 
against the cast iron saw table (Figure 7). 
Then tap down the extension table at various 
points along its edge where it meets the saw 
table, until it is level with the saw table 
(Figure 8).  As one part of the edge becomes 
level with the table, tighten the clamp on that 
side.  Then move to the other side and repeat, 
until the full length of the edge is level with the 
saw table.  Lay a straight edge across both 
extension table and saw table to ensure proper 
leveling. 

When extension table is properly aligned, holes 
need to be drilled into the wood table using the 
holes in the rails as your guide (Figure 9). 

You may 

wish to drill 3/32" pilot holes first

.  

3.  Drill 1/4" holes into the front edge of the table 

using the holes in the front rail as a guide. Drill 
1/4" holes into the back edge of the table using 
the holes in the back rail as a guide. 

4.  Install three 1/4 x 1-1/2 flat head screws, three 

1/4 flat washers, and three 1/4 hex nuts into 
the holes in the front edge of extension table 

 

Figure 7 

 

 

Figure 8 

 

 

Figure 9 

 

 

Figure 10 

Содержание XACTA

















Отзывы: