background image

 

 

IMPORTANT SAFETY INSTRUCTIONS 

WARNING – To reduce risk of injury: 

 

Read and understand the entire owner’s manual before using the pallet truck. 

 

Do not place hands or feet under the pallet truck at any time. 

 

Do not operate a loaded pallet truck on ramps or inclines. 

 

Do not tip load pallet truck forks. This may cause damage to the forks and personal injury if the rear of the 
pallet truck suddenly “pops up.” 

 

Never leave a loaded pallet truck unattended in the raised position. Always lower load to the floor. 

 

Do not load pallet truck beyond its rated capacity. 

 

Secure load before transporting. 

 

To prevent accidental tipping, make sure load is centered on the forks. 

 

Do not move a loaded pallet truck by other than manual force.  

 

Failure to comply with these warnings may result in personal injury and/or property damage. 

 

Replace warning labels if they become obscured or removed. 

 

 

WARNING:

 This product can expose you to chemicals including lead and cadmium which are known to 

the State of California to cause cancer and birth defects or other reproductive harm, and phthalates which 
are known to the State of California to cause birth defects or other reproductive harm. For more information 
go to http://www.p65warnings.ca.gov. 

 

 

Introduction 

To better understand the proper use and safe operation of your JET PTW Series Premium Pallet Truck, please 
take a few minutes to carefully read and follow the instructions contained in this manual. When finished reading 
and understanding the manual, please file in a safe and convenient location for the life of the pallet truck. 

You will notice several important features about your JET Premium Pallet Truck. It features a 2-7/8” lowered 
height, rounded fork tips and nylon entry/exit rollers to provide easy entry and exit of pallets.   

A large, easy-to-use ergonomic handle with a 200

°

 turning radius allows maximum maneuverability. The 

articulated steer wheel axle helps maintain floor contact on uneven surfaces. 

The cast iron pump design features top-of-the-stroke and overload by-pass systems, hardened and chromed 
ram and piston, and a single point valve service for easy replacement. A special lowering valve allows you to 
control the rate of descent and prevent “shock” loads. 

Your JET Premium Pallet Truck is designed and built to offer consistent, long-term operation with minimal 
maintenance and service attention. 

 
 
 

 

 

 

Содержание PTW-2036













Отзывы: