background image

4

Grounding Instructions 

 
Caution: This tool must be grounded while in use to protect the operator from electric shock. 
 

In the event of a malfunction or breakdown, grounding provides a path of least resistance for 

electric current to reduce the risk of electric shock. This tool is equipped with an electric cord 

having an equipment-grounding conductor and a grounding plug. The plug must be plugged 

into a matching outlet that is properly installed and grounded in accordance with all local codes 

and ordinances. 

 
Do not modify the plug provided. If it will not fit the outlet, have the proper outlet installed by a qualified 
electrician. 
 
Improper connection of the equipment-grounding conductor can result in a risk of electric shock. The 
conductor, with insulation having an outer surface that is green with or without yellow stripes, is the 
equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not 
connect the equipment-grounding conductor to a live terminal. 
 
Check with a qualified electrician or service personnel if the grounding instructions are not completely 
understood, or if in doubt as to whether the tool is properly grounded. Use only three wire extension 
cords that have three-prong grounding plugs and three-pole receptacles that accept the tool’s plug. 
 
Repair or replace a damaged or worn cord immediately. 
 
 

115 Volt Operation 

 
As received from the factory, your dust collector is ready to run at 115 volt operation. This dust collector, 
when wired for 115 volts, is intended for use on a circuit that has an outlet and a plug that looks the one 
illustrated in Figure A. A temporary adapter, which looks like the adapter as illustrated in Figure B, may 
be used to connect this plug to a two-pole receptacle, as shown in Figure B if a properly grounded outlet 
is not available. The temporary adapter should only be used until a properly grounded outlet can be 
installed by a qualified electrician. This adapter is not applicable in Canada. The green colored rigid 
ear, lug, or tab, extending from the adapter, must be connected to a permanent ground such as a 
properly grounded outlet box, as shown in Figure B. 
 
 
 

 
 

Содержание M-708640














Отзывы: