background image

 

Tailstock: 

Tailstock quill taper ......................................................................................................................................... MT-2 

Tailstock bore .................................................................................................................................. 3/8 in. (10 mm) 

Tailstock quill travel .................................................................................................................... 4-1/4 in. (108 mm) 

Tailstock quill thread ................................................................................................................. acme, 3/4”-10 (LH) 

 

Materials: 

Legs .......................................................................................................................................................... cast iron 

Bed ............................................................................................................................................................ cast iron 

Headstock ................................................................................................................................................. cast iron 

Headstock spindle ........................................................................................................................................... steel 

Tailstock .................................................................................................................................................... cast iron 

Tailstock quill ............................................................................................................. steel, with laser etched scale 

Tool support and base .............................................................................................................................. cast iron 

 

Dimensions: 

Tool rest width ................................................................................................................................ 14 in. (356 mm) 

Tool rest post diameter ................................................................................................................... 1 in. (25.4 mm) 

Leg footprint ............................................................................................................... 54 x 20 in. (1372 x 508 mm) 

Bed length .................................................................................................................................... 53 in. (1346 mm) 

Bed width ................................................................................................................................... 7-1/8 in. (181 mm) 

Bed gap ..................................................................................................................................... 1-3/4 in. (44.5 mm) 

Centerline spindle to floor: 

  without risers ....................................................................................................................... 39-1/4 in. (997 mm) 

  with risers ....................................................................................................................... 43-1/4 in. (1098.5 mm) 

Tool rest post diameter ................................................................................................................... 1 in. (25.4 mm) 

Shipping dimensions (LxWxH) ............. ……………………………………..57 x 31 x 28 in. (1448 x 788 x 711 mm) 

Overall dimensions, assembled (LxWxH) ........... …………………….73 x 52-1/2 x 20 in. (1854 x 1334 x 508 mm) 

Bed Extension length 

(optional accessory)

 .................................................................................... 20 in. (508 mm) 

 

Weights: 

Net weight (approx..) ..................................................................................................................... 418 lbs (190 kg) 

Shipping weight (approx..) ............................................................................................................ 484 lbs (220 kg) 

 

 

L= length; W=width; H=height 

 

The specifications in this manual were current at time of publication, but because of our policy of continuous 
improvement, JET reserves the right to change specifications at any time and without prior notice, without incurring 
obligations.

 

 

 

 

 

 

Содержание JWL1440-TREA






































Отзывы: