background image

 

 

7.  Setup and adjustments 

General note: 
Setup and adjustment work may only be carried out 
after the machine is protected against accidental 
starting by pulling the mains plug. 

 

7.1 Changing the sawblade 

The sawblade has to meet the technical specification. 

Choose a suitable sawblade, according to the cutting 
operation and according to the material to be cut. 

For high rip cuts: 
- use a wide sawblade (e.g. 13mm), coarse teethed. 

For narrow curved cuts: 
- use a narrow sawblade (e.g. 6mm). 

Check sawblade for flaws (cracks, broken teeth, bending) 
before installation. Do not use faulty sawblades. 

The sawblade teeth must point in cutting direction (down) 

Always wear suitable gloves when handling sawblades. 

The sawblades may only be changed when the mains plug 
is pulled! 

 

Replacing the bandsaw blade

  

Note:

 

The  JWBS-10  Band  Saw  comes  equipped  with  a 

factory-installed 

1712x9.5x0.35

(67.5"  x  0.375"  x  0.014"), 

6TPI blade . 

Disconnect machine from power source. 

Open upper and lower doors (Figure 22) by rotating the 
knobs. 

Loosen lock knob (G, Figure 21) and pull extension (H, 
Figure 22) away from table. 

 

Fig.21 

Remove guide rail (E, Figure 9). 

Release tension on blade by moving tension handle (Q, 
Figure 23) to the right. 

Refer to Figure 22: 

Remove  blade  from  upper  and  lower  wheels  (K,L)  and 
from between upper and lower blade guides (M,N).  

Remove blade through slot (O) in table. 

Guide  the  new  blade  through  table  slot  (O)  leading  with 
the  smooth  edge.  Place  it  around  the  upper  and  lower 
wheels and into the upper and lower blade guides (M,N). 

Note: The blade teeth should face the operator, and they 
should point down toward the table. 

Position  the  blade  to  track  in  the  middle  of  the  rubber 
tires on the wheels (K,L). 

Engage  tension  on  the  blade  by  moving  quick  tension 
handle (Q, Figure 23) to the left. 

Replace guide rail (E, Figure 9). 

Before  operating  the  saw,  check  that  the  blade  is 
tracking and has proper tension. 

 

Fig. 22 

 

 

7.2 Blade tension adjustment

 

Refer to Figure 23: 

The blade tension knob (P) is used to adjust blade tension. 

The quick tension lever (Q) must be engaged (moved to the 
left) before making tension adjustments with knob (P). 

All bearings on upper and lower guides must be clear of 
blade. 

Disconnect machine from power source. 

Apply just enough tension to take slack out of blade. 

Turn one wheel a few times to allow blade to position itself 
in center of tire. 

Note: If blade does not center, Adjusting blade tracking. 

Содержание JWBS-10


















Отзывы: