Jet JWBG-8NW Скачать руководство пользователя страница 8

 

6.4

  Mounting the grinder 

The grinder is provided with rubber pads to help 
prevent movement on a bench. For best results, 
however, it is recommended the grinder be bolted 
to the work surface or a grinder stand (fasteners 
not included). 

1.  Align mounting holes on grinder with predrilled 

holes in a bench or grinder stand. Refer to 
Figure 2 for hole spacing. 

2.  Insert bolts through the holes, and tighten 

using washers and nuts. 

 

Figure 2:  mounting holes 

6.5

  Exhaust ports 

A collection system designed for metal dust and 
swarf can be connected to the two exhaust ports at 
rear of grinder.  

 

Do not connect a dust 

collector designed for wood dust and shavings 
to the bench grinder, as this can pose a fire 
hazard. Use only a dust capture system 
designed for metal dust and swarf.

 

6.6

  Assembling eye shield brackets 

to spark guards 

Refer to Figure 3. 

Note:

 Spark guards (A) and Brackets (D) are 

marked 

L

 for left side assembly and 

R

 for right side 

assembly. 

1.  Assemble the left spark guard (A) and eye 

shield bracket (D) using Figure 3 as a guide. 
Make sure spark guard and bracket are 
marked 

L

2.  Install the right assembly in the same manner. 

 

Figure 3:  brackets to spark guards 

6.7

  Installing spark guards/brackets 

Refer to Figure 4.

 

1.  Install the left spark guard and bracket to the 

left wheel housing with two 1/4 x 3/8 hex cap 
screws (L) and two 1/4 flat washers (M). 

2.  The spark guard should be adjusted to within 

1/16" of the grinding wheel surface or other 
accessory being used. 

3.  Install the right spark guard and bracket in the 

same manner. 

Note: 

As the wheel wears down, the spark guards 

should be readjusted to maintain the 1/16" distance 
from wheel. 

6.8

  Eye shields 

Refer to Figure 4. 

The eye shields (T) are identical and will fit on 
either side of the grinder.  

1.  Insert two 3/16 x 3/8 pan head screws (K) 

through the eye shield bracket, eye shield (T), 
and eye shield plate (G) which contains 
threaded holes. 

2.  Tighten the screws (K). 

6.9

  Tool rests 

Refer to Figure 4. 

Note:

 There is a 

left

 and a 

right

 tool rest. Refer to 

Figure 4 to ensure that you install them correctly. 
(The beveled edge of tool rest faces the wheel.) 

1.  Install the left tool rest bracket (Q) by threading 

two 5/16 x 3/4 hex cap screws (H) through two 
5/16 flat washers (J) and the tool rest bracket 
(Q) into the wheel housing. 

2.  Place the tool rest (O) over the bracket (Q) so 

that the scale is seen through the cutout. 
Secure with knob (S). 

3.  Install the right tool rest in the same manner. 

Содержание JWBG-8NW





















Отзывы: