roll up sleeves above the elbows.
Remove all loose clothing and confine
long hair.
Wear safety shoes
; never wear
leisure shoes or sandals.
Always wear the approved working
outfit:
- safety goggles
- ear protection
- dust protection
Do not wear gloves while operating this
machine.
Install the machine so that there is
sufficient space for safe operation and
workpiece handling.
Keep work area well lighted.
The machine is designed to operate in
closed rooms and must be placed
stable on firm and levelled table
surface.
Make sure that the power cord does
not impede work and cause people to
trip.
Keep the floor around the machine
clean and free of scrap material, oil
and grease.
Stay alert!
Give your work undivided attention.
Use common sense. Do not operate
the machine when you are tired.
Keep an ergonomic body position.
Maintain a balanced stance at all
times.
Do not operate the machine under the
influence of drugs, alcohol or any
medication. Be aware that medication
can change your behaviour.
Never reach into the machine while it
is operating or running down.
Keep children and visitors a safe
distance from the work area.
Never leave a running machine
unattended. Before you leave the
workplace switch off the machine.
Do not operate the electric tool near
inflammable liquids or gases.
Observe the fire fighting and fire alert
options, for example the fire
extinguisher operation and place.
Do not use the machine in a dump
environment and do not expose it to
rain.
Wood dust is explosive and can also
represent a risk to health.
Dust form some tropical woods in
particular, and from hardwoods like
beach and oak, is classified as a
carcinogenic substance.
Always use a suitable dust extraction
device
Before machining, remove any nails
and other foreign bodies from the
workpiece.
Make sure to guide and hold the
workpiece thigh during machining.
Machine only stock which rests
securely on the table.
Specifications regarding the maximum
or minimum size of the workpiece must
be observed.
Do not remove chips and workpiece
parts until the machine is at a
standstill.
Do not stand on the machine.
Connection and repair work on the
electrical installation may be carried
out by a qualified electrician only.
Have a damaged or worn power cord
replaced immediately.
Replace any torn or worn sanding belt
respectively sanding disc immediately.
Make all machine adjustments or
maintenance with the machine
unplugged from the power source.
3.3 Remaining hazards
When using the machine according to
regulations some remaining hazards
may still exist.
The moving sanding belt respectively
sanding disc can cause injury.
Risk of kickback. The workpiece is
caught by the moving sanding belt
respectively sanding disc and thrown
back to the operator.
Thrown workpiece parts can lead to
injury.
Sanding dust and noise can be health
hazards. Be sure to wear personal
protection gear such as safety goggles
and dust mask. Use a suitable dust
exhaust system.
Defective sanding belts respectively
sanding discs can cause injuries.
The use of incorrect mains supply or a
damaged.
4. Machine specifications
4.1 Technical data
Belt size (WxL)
150x1220mm
Belt table size (WxL)
190x330mm
Belt table tilt
-45° to 0°
Belt speed
12m/sec
Sanding disc diameter
300mm
Disc table size (WxL)
230x420mm
Disc table tilt
-45° to +15
Disc speed
2400 rpm
Dust port diameter
100mm
suction at 20 m/sec
560m3/h
Overall (LxWxH)
830x700x1400mm
Net weight
110kg
Mains
230V ~1/N/PE 50Hz
Output power
1,1 kW (1,5HP) S1
Reference current
7A
Extension cord (H07RN-F): 3x1,5mm²
Installation fuse protection
16A
4.2 Noise emission
Acoustic pressure level (EN 11202):
Idling
71,9 dB (A)
In operation
84,1 dB (A)