manualshive.com logo in svg

Jet JFM-5, Инструкция по эксплуатации и каталог запасных частей

Поделиться
Скачать
Jet JFM-5 Скачать руководство пользователя страница 12

 

12

Chuck Extension Adaptor 

The Mortiser is supplied with a chuck intended 
for use with augers having long shanks. Augers 
come with long or short shanks, depending upon 
the manufacturer. See Figure 10.  

The chuck extension adaptor is used for 
mounting a short-shank auger. Proceed as 
follows (Figure 11): 

1.  Remove chisel and auger. 

2.  Hold the spindle still by inserting the chuck 

key into the chuck and allowing it to wedge 
against the edge of the headstock. Use the 
provided chuck removal wrench to lower the 
chuck release nut, which will force the chuck 
off the spindle. Catch the chuck when it falls 
to prevent it being damaged. 

3.  Return the chuck release nut to its former 

high position on the spindle. 

4.  Push the optional adaptor onto the spindle 

as shown. Then firmly push the chuck onto 
the adaptor.  

Tool Storage 

A shelf and perforated cushion inside the 
cabinet are convenient for storing the 
accessories.  

The chuck key can also be stored on the clips at 
the rear of the mortiser column (see Figure 7). 

Grounding Instructions 

  Electrical connections must 

be made by a qualified electrician in 
compliance with all relevant codes. This 
machine must be properly grounded to help 
prevent electrical shock and possible fatal 
injury. 

In the event of a malfunction or breakdown, 
grounding provides a path of least resistance for 
electric current to reduce the risk of electric 
shock. The mortiser is equipped with an electric 
cord having an equipment-grounding conductor 
and a grounding plug. The plug must be inserted 
into a matching outlet that is properly installed 
and grounded in accordance with all local codes 
and ordinances. Do not modify the plug provided 
– if it will not fit the outlet, have the proper outlet 
installed by a qualified electrician. 

Improper connection of the equipment-
grounding conductor can result in a risk of 
electric shock. The conductor with insulation 
having an outer surface that is green with or 
without yellow stripes is the equipment-
grounding connector. 

 

Figure 10 

 

Figure 11 

The chuck access cover has been removed for 

clarity. Do not operate the mortiser without cover 

in place. 

 

 

 

 

 

 

 

 

 

 

 

 

Содержание JFM-5

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды