Jet JDP-17MF Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 24

background image

9

Contents of the Shipping Container

1. Head

Assembly

1. Table
1. Column and Bracket Assembly
1. Base
1. Owner’s

Manual

1. Warranty Registration Card
1. Chuck and Chuck Key
3. Downfeed

Handle

1.  Table Bracket Lock Handle
1.  Table Bracket Raising Handle
4.  M10 x 40 Hex Cap Bolts
1. Arbor
1. Drift

Key

Tools Supplied for Assembly

1. 3mm Hex Wrench
1. 5mm Hex Wrench

Tools Required for Assembly

1. 17mm Box Wrench or a 6”-8” Adjustable

Wrench

,

WARNING!

Read and understand all assembly

instructions before attempting assembly!

Failure to comply may cause serious injury!

Before Assembly

1. Remove the contents from the shipping

container.

2. Compare the contents of the shipping

container with the list found above. Report
any shortages or damage to your JET
distributor.

3. Clean all rust protected surfaces with

kerosene or a light solvent. Do not use
lacquer thinner, paint thinner, or gasoline.
These will damage plastic components and
painted surfaces.

«
...
7
8
9
10
11
...
»

Содержание JDP-17MF

























Отзывы:

Нет отзывов

Похожие инструкции для JDP-17MF

Бренд: Accu-Turn Страницы: 96

Бренд: ICP Страницы: 38

Бренд: Kärcher Страницы: 148

Бренд: Keithley Страницы: 10

Бренд: Vanderbilt Страницы: 18

Бренд: Campbell Hausfeld Страницы: 32

Бренд: Wacker Neuson Страницы: 32

Бренд: Sears Страницы: 4

Бренд: Timberline Tool Страницы: 6

Бренд: Far Tools Страницы: 24

Бренд: Elaflex Страницы: 16

TRIO-PS-2G/3AC/24DC/40

Бренд: Phoenix Contact Страницы: 25

Бренд: LOVATO ELECTRIC Страницы: 4

Бренд: Neilsen Страницы: 4

Бренд: ADC Страницы: 4

Бренд: McPower Страницы: 8

Бренд: Ignite Страницы: 54

Бренд: Sealey Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды