Jet IBG-8, Инструкция по эксплуатации и каталог запасных частей

Страница: 10 / 36

10
6.0 Electrical connections
Electrical connections should
be made by a qualified electrician in
compliance with all relevant codes. This tool
must be properly grounded.
The model IBG-8 (#578008) and IBG-10
(#578010) bench grinders are prewired for 115V
power, and are supplied with a plug designed for
use on a circuit with a grounded outlet that looks
like the one pictured in A, Figure 8. These grinders
may be converted to 230V power, see
sect. 6.3.
The model IBG-12 (#578012) is rated for 230V
only, and is not supplied with a plug.
Before connecting to power source, be sure switch
is in
off position.
It is recommended that the grinders (all models) be
connected to a 15 amp circuit with a 15 amp circuit
breaker or time-delay fuse marked “D”.
Local
codes take precedence over recommendations.
Figure 8: plug configurations
6.1 Grounding instructions
1. All Grounded, Cord-connected Tools:
In the event of a malfunction or breakdown,
grounding provides a path of least resistance for
electric current to reduce the risk of electric shock.
This tool is equipped with an electric cord having
an equipment-grounding conductor and a
grounding plug. The plug must be plugged into a
matching outlet that is properly installed and
grounded in accordance with all local codes and
ordinances.
Do not modify the plug provided - if it will not fit the
outlet, have the proper outlet installed by a
qualified electrician.
Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. The
conductor with insulation having an outer surface
that is green with or without yellow stripes is the
equipment-grounding conductor. If repair or
replacement of the electric cord or plug is
necessary, do not connect the equipment-
grounding conductor to a live terminal.
Check with a qualified
electrician or service pe r sonnel if the
grounding instructions are not completely
understood, or if in doubt as to whether the
tool is properly grounded. Failure to comply
may cause serious or fatal injury.
Use only 3-wire extension cords that have 3-prong
grounding plugs and 3-pole receptacles that accept
the tool's plug.
Repair or replace damaged or worn cord
immediately.
2. Grounded, cord-connected tools intended for
use on a supply circuit having a nominal rating
less
than 150 volts:
This tool is intended for use on a circuit that has an
outlet that looks like the one illustrated in
A, Figure
8. An adapter, shown in B and C , may be used to
connect this plug to a 2-pole receptacle as shown
in
B if a properly grounded outlet is not available.
The temporary adapter should be used only until a
properly grounded outlet can be installed by a
qualified electrician.
This adapter is not permitted
in Canada. The green-colored rigid ear, lug, and
the like, extending from the adapter must be
connected to a permanent ground such as a
properly grounded outlet box.
3. Grounded, cord-connected tools intended for
use on a supply circuit having a nominal rating
between
150 - 250 volts , inclusive:
This tool is intended for use on a circuit that has an
outlet that looks like the one illustrated in
D, Figure
8. A grounding plug may be installed, that looks
like the plug illustrated in
D ; or the grinder may be
“hard-wired” to a panel, provided there is a
disconnect for the operator.
Make sure the tool is connected to an outlet having
the same configuration as the plug. No adapter is
available or should be used with this tool. If the tool
must be reconnected for use on a different type of
electric circuit, the reconnection should be made by
qualified service personnel; and after reconnection,
the tool should comply with all local codes and
ordinances.
6.2 Extension cords
The use of extension cords is discouraged. Try to
position equipment near the power source. If an
extension cord becomes necessary, use only
three-wire extension cords that have three-prong
grounding type plugs and three-prong receptacles
that accept the tool's plug. Replace or repair
damaged or worn cord immediately.
Make sure your extension cord is good condition,
and is heavy enough to carry the current your
product will draw. An undersized cord will cause a
drop in line voltage resulting in loss of power and
overheating.