background image

 

Base Unit Assembly 

Base 

1. Install 

four

 casters to the underside of the base as 

pictured in Fig. 2. 

Referring to Figure 1: 

2. Thread 

the 

hex nut

 (B) onto the caster shaft. Then 

slide the 

lock washer

 (A) over the caster shaft. 

Thread the caster shaft into the threaded hole on 
the underside of the base, turn until snug. Tighten 
the 

nut

 (B) against the base with a 14mm wrench. 

This will give the caster proper clearance. 

 

 

Motor and Fan Assembly 

Referring to Figure 2: 

3. Place the 

base

 (C) with casters on the ground. 

Attach the 

motor and fan assembly

 (A) to the base 

using four each M8 x 16 hex cap screws, and M8 
flat washers (B). Tighten with a 13mm wrench. 

The dust collector must not be 

connected to the power source during assembly. 
Failure to comply may result in serious injury!

 

 

Referring to Figure 3: 

4. Attach 

impeller cover

 (A) to 

impeller housing 

(D) 

using eight M6 x 12 

pan head screws

 (B). Press 

the 

inlet ports

 (C) onto the inlet guard until it snaps 

into place. 

 To reduce the risk of injury from 

moving parts, always keep inlet port covered with 
the caps provided, if they are not connected to a 
hose. Failure to comply may result in serious 
injury! 

 

 

 

 

Connector Housing 

5. Attach 

three 

support

 

legs

 (A, Fig. 4) to the base 

using six M8 x 16 hex cap bolts and six M8 flat 
washers (B, Fig. 4). Hand-tighten only at this time. 

 

 

 

Figure 1 

 

Figure 2 

 

Figure 3 

 

Figure 4 

Содержание DC-1100CK

























Отзывы: