background image

JET   

 

About this manual 

This manual is provided by JET, covering the safe operation and maintenance procedures for a JET Model 
JAT-650  and  JAT-651  Pneumatic  Screwdriver.  This  manual  contains  instructions  on  safety  precautions, 
general operating procedures, maintenance procedures and parts breakdown. Your tool has been designed 
and constructed to provide consistent, long-term operation if used in accordance with the instructions set 
forth in this document. 

The instructions and warnings in this manual may not encompass all possible workplace environments. The 
operator  is  expected  to  take  appropriate  precautions  and  exercise  common  sense.  As  with  any  tool 
operation, safety of operator and bystanders should be first priority. 

If there are questions or comments, please contact your local supplier or JET. JET can also be reached at 
our web site: www.jettools.com. 

Record the serial number and purchase information of your tool on the cover of this manual for quick access. 
Retain this manual for future reference. If the tool transfers ownership, the manual should accompany it. 

Register your product using the mail-in card provided, or register online:  

http://www.jettools.com/us/en/service-and-support/product-registration/ 

 

Содержание 505650

















Отзывы: