manualshive.com logo in svg

Jet 505124, Руководство по эксплуатации и запасным частям, Страница: 6 / 16

Поделиться
Скачать
Jet 505124 Скачать руководство пользователя страница 6

6 

JAT-124 Impact Wrench 

 

Tool specifications

 

Model number 

JAT-124 

Stock number 

505124 

Square drive 

1/2 in. 

Bolt capacity 

9/16 in. 

Anvil retainer type 

Hog ring 

Impact mechanism 

Jumbo hammer 

Maximum torque 

180 lbf•ft  (244.05 N•m) 

Working torque 

45-140 lbf•ft  (61.01-189.81 N•m) 

Free speed  

7,000 RPM 

Blows per minute 

1400 

Average air consumption 

5 CFM 

Air inlet 

1/4 in. NPT 

Air hose inside diameter  

3/8 in. 

Required air pressure 

90 psi (621 kPa) 

Vibration value 

43.5 m/s

2

 

Noise level 

1

 108 

dB

(A)

 

Power setting 

2-speed forward, 1-speed reverse 

Grip Inline 

Overall Length 

13.4 in. (340.36 mm) 

Housing material 

                                    Aluminum alloy with plastic shell

 

Net weight  

3.97 lb. (1.8 kg) 

Shipping weight 

4.19 lb. (1.9 kg) 

1

 The specified values are emission levels and are not necessarily to be seen as safe operating levels. As 

workplace conditions vary, this information is intended to allow the user to make a better estimation of the 
hazards and risks involved only. 

 

 

Specifications were current at time of publication, but because of our policy of continuous improvement, JET 
reserves the right to change specifications at any time and without prior notice, without incurring obligations. 

Содержание 505124

















Отзывы:

Нет отзывов