Jet-tech 737E Скачать руководство пользователя страница 12

 

 

 

 

STARTING THE MACHINE

 

1- Verify that there are sufficient levels of detergent and rinse 

additive. The end weight at the end of the red (detergent) and blue 

(rinse) supply tubes must be at the bottom of the chemical 

containers. The chemicals will automatically dispensed at the 

appropriate times. 

2- Open the dishwasher door and verify that all internal components, 

filters, wash arms and drain tube, are in their correct positions. 

(Fig.1) 

3- Close the door and press button “A” to turn ON the machine. 

(Fig.2) The dishwasher will start to fill. During the fill process, the 

display will show “FILL”. (Fig.3) 

 - If during this process the door is opened, “CLOSE DOOR” is 

displayed. Closing the door will continue the fill process. 

4- Once the dishwasher has filled, the rinse water will heat to 185°F 

and then the wash water will heat to 165°F. When this initial heating 

process is finished (approximately 20-30 minutes), the Start Washing 

Cycle (button “B”) will change colors from AMBER to GREEN. The 

machine is now ready to use.

 

 

– WASHING CYCLE 

The wash cycle includes a hot water washat 165°F with detergent and a 

rinse cycle with sanitizing hot water at 185°F with rinse aid.  

When the machine reaches the correct temperature and it is ready to start 

a new cycle, the button "B" will turn green, then:  

1- Open the door. 

2- Slide the pre-rinsed, soiled dish basket in the dishwasher and close the 

door. 

3- Press one of the available cycles between button “C-2 minutes”, “D-3 

minutes” or “E-4 minutes”. (Fig.4) 

4- Press button “B” start washing cycle. (Fig.5) 

5- Wait until the Display Panel (Q) shows “END” indicating that the cycle 

finished (Fig.6). Open the dishwasher door and remove clean dish 

basket.The dishes will air dry in several minutes. 

 - During the wash cycle, the GREEN indicator light is blinks (button “B”) 

and remaining time is displayed. 

 - If during this process the door is opened, the washing cycle is 

interrupted and “CLOSE DOOR” is displayed. To start a new cycle press 

button “B” start cycle. 

N.B.: The machine is equipped with different washing cycles, from 2 to 4 

minutes. Choose button “C” short cycle for light soiled dishes. Button “D” 

medium cycle for medium soiled dishes. Button “E” long cycle for very 

soiled dishes.

 

 

 

 

 

 

 

 

 

12

 

 

 

 

 

 

 

 

 

 

Fig. 1

 

 

 

 

 

 

Fig. 2

 

 

 

 

 

Fig. 3

 

 

 

 

Fig. 4

 

 

 

 

 

 

 

 

 

 

Fig. 5

 

 

 

 

Fig. 6

 

Содержание 737E

















Отзывы: