10
5.
Remove the level and close the drawers. Recheck the gap
between the top of the drawer and the countertop. If the gap
measures less than
³⁄₈
" (9.5 mm), turn all four leveling bolts
equally to raise the leveling legs (this will lower the appliance).
Recheck the level.
NOTE:
Be sure to recheck the horizontal level of the top
drawer.
6.
Be sure all four levelers are on the floor and supporting the
full weight of the refrigerator drawers.
Install Custom Overlay Panel
IMPORTANT:
■
Create a custom overlay panel according to the
specifications in “Custom Overlay Drawer Panels.”
■
Jenn-Air is not responsible for the removal or addition of
molding or decorative panels that would not allow access to
the refrigerator for service.
Attach the Overlay Panel
NOTE:
If the overlay hooks are not installed, see “Custom
Overlay Drawer Panels” for overlay hook locations. The location
of the hooks must be as precise as possible. If the custom panel
is incorrectly placed, the panel may interfere with optimal use of
the drawers.
1.
Attach the custom handle of your preference on the overlay
before attaching the overlay to the drawer of the refrigerator.
NOTE
: Custom handles may vary in dimensions. Holes must be
made on the panel according the specific dimensions of your
handle.
2.
Attach the hooks to their corresponding recessions on the
panel, using the SS Flat M4x12 screws. Two screws are
needed per hook. The hooks must be on the outer edge of
the panel.
3.
Gently pull back the gasket from the top corners of the door
until you can see the screw that is behind the gasket. There is
one screw on each side. It is not necessary to remove the
gasket.
4.
Remove the screws behind the gasket (one per side).
5.
Align the panel to the drawer and position the overlay panel
½” (1.27cm) higher than the door. Position the overlay hooks
with the pilot holes and push the hooks into the holes. The
drawer has insulant foam in its interior so you may feel some
interference while pushing. Push until the hooks go through
the foam.
6.
Push straight down on the overlay panel to secure the overlay
hooks to the drawer.
7.
Using the self-tap wood screws (two per drawer; one in each
corner of the drawers), attach the panel to the drawer.
NOTE
: Do not put the screws removed in step 4 back on the
door.
8.
Once the overlay is securely attached to the drawer with the
two screws, put the gasket back in its place by pressing it
against the door until the gasket is even and firmly secured.
Complete Installation
1.
Remove all boxes, parts packages and packing materials
from the interior of the refrigerator drawers.
2.
Remove the film.
3.
Clean the refrigerator drawers before use.
4.
The controls are preset at the factory to the recommended
settings. Be sure that the compressor is operating properly
and that all the lights are working.
5.
If construction will continue after the refrigerator drawers
have been installed, turn OFF the power for both drawers.
To get the most efficient use from your new refrigerator drawers,
read the “Refrigerator Drawers Use” section.
REFRIGERATOR
DRAWERS USE
Normal Sounds
Your new refrigerator drawers may make sounds that your old
refrigerator drawers didn’t. Because the sounds are new to you,
you might be concerned about them. Most of the new sounds are
normal. Hard surfaces, such as the floor, walls, and cabinets, can
make the sounds seem louder. The following describes the kinds
of sounds and what may be making them.
■
Your refrigerator drawers are designed to run more efficiently
to keep your food items at the desired temperatures and to
minimize energy usage. The high efficiency compressor and
fans may cause your refrigerator drawers to run longer than
your old ones. You may also hear a pulsating or high-pitched
sound from the compressor or fans adjusting to optimize
performance.
■
You may hear the evaporator fan motor circulating air through
the refrigerator drawers. The fan speed may increase as you
open the drawers or add warm food.
■
As each cycle ends, you may hear a gurgling sound due to
the refrigerant flowing through the sealed system tubing.
■
Contraction and expansion of the inside walls may cause a
popping noise.
■
You may hear air being forced over the condenser by the
condenser fan.
■
You may hear water running into the drain pan during the Off
cycle.
Ensuring Proper Air Circulation
In order to ensure proper temperatures, you need to permit
airflow inside the drawers.
Do not block any airflow vents. If the vents are blocked, airflow
will be obstructed and temperature and moisture problems may
occur.
IMPORTANT:
To avoid odor transfer and drying out of food, wrap
or cover foods tightly.
Содержание W10741583B
Страница 55: ...55...
