background image

9

3-Wire Cable from Power Supply to 3-Wire Cable 

from Cooktop

IMPORTANT:

 Use the 3-wire cable from power supply where 

local codes permit connecting the frame-ground conductor to 

the neutral (white) junction box wire:

1. 

Disconnect power.

2. 

Remove junction box cover, if present.

3. 

Connect the flexible cable conduit from the cooktop to the 

junction box using a UL listed or CSA approved conduit 

connector.

4. 

Tighten screws on conduit connector if present.

5. 

Connect the two black wires together using the UL listed 

wire connectors.

6. 

Connect the two red wires together using the UL listed wire 

connectors.

7. 

Connect the green or bare cooktop cable wires to the white 

(neutral) wire in the junction box using the UL listed wire 

connectors.

8. 

Install junction box cover.

9. 

Reconnect power.

Attach Cooktop to Countertop

NOTE:

 This section applies only if you are using clamping 

brackets.

1. 

Place the 2½" (6.4 cm) clamping screws into the outermost 

hole in the clamping bracket.

2. 

Use a screwdriver to tighten the screws against the 

countertop. Do not overtighten.

Complete Installation

1. 

Check that all parts are now installed. If there is an extra 

part, go back through the steps to see which step was 

skipped.

2. 

Check that you have all your tools.

3. 

Dispose of/recycle all packaging materials.

4. 

Use a mild solution of liquid household cleaner and warm 

water to clean cooktop before use. Dry thoroughly with a soft 

cloth. For more information, see the “Cooktop Care” section 

of the Use and Care Guide.

5. 

Read the “Cooktop Use” section in the cooktop Use and 

Care Guide.

6. 

Reconnect power.

7. 

For further information about the product, read the User 

Instructions.

NOTE:

 If the cooktop does not work after turning on the power, 

check that a circuit breaker has not tripped or a household fuse 

has not blown. See “Troubleshooting” section in the Use and 

Care Guide for further information.

If You Need Assistance or Service: 

Please reference the “Assistance or Service” section of the Use 

and Care Guide or contact the dealer from whom you purchased 

your cooktop.

H

B

C

D

E

F

G

I

A

A.  3-wire cable from power supply
B.  Red wires
C.  Green or bare ground wire 

(from cooktop)

D.  3-wire cable from cooktop

E.  Junction box
F.  White wire (from power supply)
G. UL listed wire connector
H.  Black wires
I.  UL listed or CSA approved 

conduit connector

A

B

C

D

E

F

G

A.  Glass cooktop
B.  Cooktop base
C.  Attachment screw
D.  Clamping bracket (extends far 

enough beyond cooktop base 

to allow installation of clamping 

screws)

E.  2½" (6.4 cm) clamping screw
F. Countertop
G. Foam seal

Содержание JEC3430H





















Отзывы: