background image

I

NSTALLATION

2. Align notches on back of handle

with retaining clips on doors.
Insert clips into notches and
slide handle down until it
contacts bottom trim.

3. Replace top door trim and Phillips

screws.

4. Repeat instructions 1-3 to install

other handle.

To avoid possible injury and damage to property,
tape decorative panels (select models) securely into
place before removing door handles.

WARNING

To Remove:

1. Release top door trim (select models)

by removing Phillips screws from top
of fresh food door and retain screws
for later use.

2. Grasp handle firmly with both

hands. Slide handle upward
approximately 

3

4

” to release.

3. Repeat instructions 1-2 to

remove other handle.

To Reinstall:

1. Repeat in reverse order.

Door Clip

Handle Extensions 

(select models)

To Install:

• Align and clip handle extension into position on the

handle. Press the extension over the door retainers.

To Remove:

• Slide the extension down and unclip from door

retainer.

Euro Handles

This handle style is installed at the factory.

Materials Needed:

3

32

” allen wrench

To Remove:

• Remove set screw from

handle mounting post
using 

3

32

” allen wrench.

• Repeat the procedure on

all posts to remove the
handle.

To Replace:

• Align handle with the mounting posts.

• Fully tighten all set screws to secure handle 

in place.

Full-Length Aluminum Handles

To Install:

1. Release top door trim (select models)

by removing Phillips screws from top
of fresh food door and retain screws
for later use.

7

Содержание JCD2295KE








Отзывы: