background image

5

H

OW TO

R

EVERSE

R

EFRIGERATOR

D

OOR

DOORS WITH TRIM AND
PANELS

1. Perform all steps listed in How to

Remove the Door and Hinges.

2. Perform removal steps listed in How

to Remove and Install Handles.

3. Transfer cabinet

plugs and screws to
opposite side of
cabinet.

4. Remove plugs with

flat blade of
s c r e w d r i v e r
wrapped in masking
tape.

5. Remove center mullion screws with

5

16

" hex head driver.

6. Locate door stop (B) and door cap (A)

on bottom edge of fresh food door.
Remove with a Phillips screwdriver.

• Retain all items for later replacement.

7. Remove side door trim (A) and

handle side trim (B) from door by
tapping bottom edges upward with a
soft rubber mallet.

• Trim will slide up approximately 

3

4

"

and release from
door.

8. Rotate door panel

180° and tape in place.

9. Remove top door

extension with 

1

4

" hex

head driver. Flip door
extension (A) so notched corner
turns in toward interior of door (B).

10. Retrieve alternate side door trim

shipped with refrigerator. Install trim
by aligning notches of trim with
metal mounting tabs on side of door.

• Slide trim down until piece locks

into place.

• Tap top of trim with rubber mallet

to insure snug fit.

• Repeat same procedure to install

handle side trim removed in step 7.

11. Replace bottom door cap (A)

removed in step 6. Install door stop
(B) on opposite side of door.

12. Remove tape from panels.

13. Proceed to next column to reinstall

handle.

To avoid possible injury and damage to
property, tape decorative panels (some
models) securely into place before
removing side door trim and handles.

WARNING:

B

A

A

B

B

 

A

 

A

B

Note:

When working directly on door, lay

the interior side of the door down
flat, nonabrasive surface. If using a
floor or table, prepare working
surface with rugs or towels to avoid
damage to door finish.

H

OW TO

I

NSTALL AND

R

EMOVE

H

ANDLES

In some cases, handles may need to be
removed to transport unit through tight
spaces, reverse doors, or install panels.

Some models may come with handles
shipped separate from the refrigerator
door.

INSTALLING HANDLES

1. Retrieve handle from shipping

material (some models).

2. Locate handle

mounting posts on
face of door.

3. Position handle over mounting

posts.

4. Tighten set screws (A)

with a 

3

32

" Allen

wrench

REMOVING HANDLES

1. Locate set screws in handle and

loosen set screws with a 

3

32

" Allen

wrench.

2. Lift handle from handle mounting

posts to remove.

Note:

In cases of door
reversal, panel installation, or panel
removal, the mounting posts must be
removed. Use a 

1

4

" hex head driver

to remove the post from the door.

A

Содержание BOTTOM FREEZER REFRIGERATOR








Отзывы: