JENCO VisionPlus 6177 Скачать руководство пользователя страница 2

Страница: 2 / 16

CONTENTS

GENERAL INTRODUCTION…………………................2

INITIAL INSPECTION……...………………....................2

POWER INPUT…….……...………………......................2

INSTALLING THE BATTERIES..…………....................3

DISPLAY & KEYS FUNCTIONS…..……………..…...…..…4

A. Display

......................................................................4

B. Keys

...........................................................................5

OPERATIONAL PROCEDURES..……..........................6

A. Buffer Set Selection

.....................................................6

B. pH Calibration

.............................................................6

a. Calibration with an ATC/Temp probe in the pH-AUTOLOCK

mode

........................................................................6

b. Calibration with manual temperature compensation in the

pH AUTOLOCK mode

....................................................7

c. Calibration with an ATC/Temp probe in the pH NON-

AUTOLOCK mode

........................................................8

d. Calibration with manual temperature compensation in the

pH NON-AUTOLOCK mode

............................................9

C. pH Measurements

........................................................9

a. Measurement with an ATC/Temp probe in the pH-AUTOLOCK

mode

........................................................................9

b. Measurement with manual temperature compensation in the

pH AUTOLOCK mode

..................................................10

c. Measurement with an ATC/Temp probe in the pH NON-

AUTOLOCK mode

......................................................10

d. Measurement with manual temperature compensation in the

pH NON-AUTOLOCK mode.

..........................................11

D. Temperature Measurements

.......................................11

E. mV Measurements

.....................................................11

Measurement in the mV-AUTOLOCK mode

....................11

Measurement in the mV NON-AUTOLOCK mode

.............11

pH BUFFERS..…………………………….....................12

ERROR DISPLAYS AND TROUBLESHOOTING.......13

SPECIFICATIONS………………..……........................14

WARRANTY…………………………….........................15

Содержание VisionPlus 6177

















Результаты поиска

Содержание VisionPlus 6177

Отзывы:

Бренды по названию

Популярные бренды

JENCO VisionPlus 6177, Руководство по эксплуатации

Результаты поиска

Содержание VisionPlus 6177

Отзывы:

Бренды по названию

Популярные бренды