JEI MAGBEAST HM200T Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 18

JEI MAGBEAST HM200T Скачать руководство пользователя страница 3

MAGBEAST HM200T

3 |

P a g e

[1] SPECIFICATIONS OF

MAGBEAST HM200T DRILLING MACHINE

Maximum hole cutting capacity in .2/.3C steel =

2

00mm dia. x 75mm deep

Tapping up to M52

Motor Unit

Voltages

230v/60Hz 110v/50-60Hz

Normal full load output

2850 W

Magnet Size

295 x 140 x 70 mm

Magnet Force at 20°C with
25mm minimum plate thickness

The use on any material less than 25mm thick will
progressively reduce the magnetic performance. If
possible, substitute material should be positioned
under the magnet and work piece to equate to a
suitable material thickness. If this is not possible, an
alternative secure method of restraining the machine
MUST be used.

2,200kg/26,800N

Overall Dimensions

Height - maximum extended

955mm

Height - minimum

730mm

Width (including Hand wheel)

280mm

Length Overall (including Guard)

455mm

Stroke

330mm

Net Weight

52kgs

Maximum hand/arm vibration magnitude
(measured at handle during operation in
accordance with ISO5349, using a 22mm cutter
through 13mm MS plate)

0.82 m/s²

Estimate of likely daily vibration exposure.
Operation 30 holes @ 2 minute/hole.

0.29m/s² A(8)

Average noise level during cutting at operator

’

s

ear position.

89dB(A)

«
1
2
3
4
5
...
»

Содержание MAGBEAST HM200T



















Отзывы:

Нет отзывов