Jegs 79009 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 16

background image

LOWERING THE JACK

1. Raise load high enough to allow clearance for the jack stands to be removed, then carefully remove jack stands.
2. Remove support stands.
3. Grasp the handle firmly with both hands. Securely hold on to the jack handle so your hands do not slip and ensure
the release valve does not rapidly lower.
4. Carefully open the Release Valve by slowly turning the handle counterclockwise. (Do not allow bystanders around
the jack or under the load when lowering the jack.
5. After removing jack from under the load, push ram and handle sleeve down to reduce exposure to rust and
contamination.

WARNING:

USE EXTREME CAUTION WHEN LOWERING THE JACK. THE JACK HANDLE MAY TURN RAPIDLY.

OPENING THE RELEASE VALVE TOO FAST CAN CAUSE THE JACK TO LOWER RAPIDLY. FAILURE TO HEAD
THESE WARNINGS COULD CAUSE SERIOUS INJURY OR DEATH.

1-800-345-4545 jegs.com

«
...
6
7
8
9
10
...
»

Содержание 79009

















Отзывы:

Нет отзывов

Похожие инструкции для 79009

Бренд: Beta Страницы: 64

Бренд: Motomaster Страницы: 6

Бренд: AC Hydraulic Страницы: 20

Бренд: AC Hydraulic Страницы: 24

Бренд: AC Hydraulic Страницы: 40

Бренд: Raider Страницы: 32

Бренд: AC Hydraulic Страницы: 24

Бренд: Kennedy Страницы: 2

Бренд: Jefferson Страницы: 8

POW'R RISER PR Series

Бренд: Enerpac Страницы: 5

Бренд: Enerpac Страницы: 32

Бренд: Gearwrench Страницы: 16

Бренд: Columbus McKinnon Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды