manualshive.com logo in svg

Jeep Grand Cherokee Wj 2000, Руководство пользователя

Поделиться
Скачать
Jeep Grand Cherokee Wj 2000 Скачать руководство пользователя страница 9

REMOVAL AND INSTALLATION

COMBINATION FLASHER

WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, REFER TO GROUP 8M - PASSIVE RESTRAINT
SYSTEMS BEFORE ATTEMPTING ANY STEERING
WHEEL,

STEERING

COLUMN,

OR

INSTRUMENT

PANEL COMPONENT DIAGNOSIS OR SERVICE. FAIL-
URE TO TAKE THE PROPER PRECAUTIONS COULD
RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT
AND POSSIBLE PERSONAL INJURY.

REMOVAL

(1) Disconnect and isolate the battery negative

cable.

(2) Remove the steering column opening cover

from the instrument panel. Refer to Steering Col-
umn Opening Cover in the Removal and Installa-
tion section of Group 8E - Instrument Panel Systems
for the procedures.

(3) Remove the combination flasher from the junc-

tion block (Fig. 4).

INSTALLATION

(1) Position the combination flasher in the proper

receptacle in the junction block.

(2) Align the combination flasher terminals with

the terminal cavities in the junction block receptacle.

(3) Push in firmly on the combination flasher until

the terminals are fully seated in the terminal cavities
in the junction block receptacle.

(4) Install the steering column opening cover onto

the instrument panel. Refer to Steering Column
Opening Cover in the Removal and Installation sec-
tion of Group 8E - Instrument Panel Systems for the
procedures.

(5) Reconnect the battery negative cable.

TURN SIGNAL AND HAZARD WARNING
SWITCH

WARNING: ON VEHICLES EQUIPPED WITH AIR-
BAGS, REFER TO GROUP 8M - PASSIVE RESTRAINT
SYSTEMS BEFORE ATTEMPTING ANY STEERING
WHEEL,

STEERING

COLUMN,

OR

INSTRUMENT

PANEL COMPONENT DIAGNOSIS OR SERVICE. FAIL-
URE TO TAKE THE PROPER PRECAUTIONS COULD
RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT
AND POSSIBLE PERSONAL INJURY.

REMOVAL

(1) Disconnect and isolate the battery negative

cable.

(2) Remove the screw that secures the lower tilting

steering column shroud to the steering column multi-
function switch mounting housing (Fig. 5).

Fig. 4 Combination Flasher

1 – COMBINATION FLASHER
2 – JUNCTION BLOCK

Fig. 5 Steering Column Shrouds Remove/Install

1 – UPPER TILTING COLUMN SHROUD
2 – FIXED COLUMN SHROUD
3 – LOWER TILTING COLUMN SHROUD
4 – SCREW

WJ

TURN SIGNAL AND HAZARD WARNING SYSTEMS

8J - 9

Содержание Grand Cherokee Wj 2000















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды